Flow blockage in a transonic axial flow compressor: simulation analysis under distorted conditions

  • Authors

    • G Srinivas
    • K Raghunandana
    • B Satish Shenoy
    2018-04-20
    https://doi.org/10.14419/ijet.v7i2.21.11833
  • Compressor, blockage, distortion, simulation, analysis.

  • Abstract

    Today the aircraft industry is looking for faster and safer engines for both civil and military applications. The performance of all different types of air breathing engines depends on the amount of mass flow rate of air entering and hot gas ejecting out from the engine. Thrust is the key role for any engine performance. To achieve more thrust all the turbo machinery components like axial fan, axial flow compressor and axial flow turbine should function effectively. This paper is primarily dealing about one of the turbo machinery component, axial flow compressor performance where the study is more focused on flow blockage formation under distorted phenomena. The complete blade boundary layer formation and related flow numerical theory are discussed in detail, accordingly the boundary conditions were set to have better numerical simulations using ANSYS tool. To find the flow blockage formation suitable turbulence model was coded using the well know compressible equations. The flow blockage between the rotor and stator of the compressor stage was calculated and also validated with that of experimental data effectively. The flow simulation results also revealed that the performance parameters under the modern engine transonic speed from Mach 0.8 to 1.2 under the distorted conditions are better for aeromechanical features.

     

     

  • References

    1. [1] Mokelke H, “The Unsteady Response of an Axial Flow Compressor with a Distorted Inlet Flowâ€, ministry of defense (procurement executive) aeronautical research council current papers, (1970).

      [2] Smith JLH, “Casing Boundary Layers in Multistage Axial-Flow Compressorsâ€, Flow Research on Blading, (1970), pp.275–304.

      [3] Koch CC, “Stalling Pressure Rise Capability of Axial Flow Compressor Stagesâ€, ASME Journal of Engineering for Power, Vol.103, (1981), pp.645–656.

      [4] Khalid S, “The Effects of Tip Clearance on Axial Compressor Pressure Rise, Ph.D. Dissertation, Massachusetts Institute of Technology, (1994).

      [5] Suder KL, “Blockage development in a transonic, axial compressor rotorâ€, ASME International Gas Turbine and Aeroengine Congress and Exhibition (pp. V001T03A059-V001T03A059), (1997).

      [6] Öztürk HK, Turner AB, Childs PRN & Bayley FJ, “Stator well flows in axial compressorsâ€, International journal of heat and fluid flow, Vol.21, No.6, (2000), pp.710-716.

      [7] Lin S, Yang C, Wu P & Song Z, “Active surge control for variable speed axial compressorsâ€, ISA transactions, Vol.53, No.5,(2014), pp.1389-1395.

      [8] Sharifi N & Boroomand M, “An investigation of thermo-compressor design by analysis and experiment: Part 1. Validation of the numerical methodâ€, Energy conversion and management, Vol.69, (2013), pp.217-227.

      [9] Chen L, Sun F & Wu C, “Optimum design of a subsonic axial-flow compressor stageâ€, Applied energy, Vol.80, No.2,(2005), pp.187-195.

      [10] Ye X, Li P, Li C & Ding X, “Numerical investigation of blade tip grooving effect on performance and dynamics of an axial flow fanâ€, Energy, Vol.82, (2015), pp.556-569.

      [11] Chang H, Zhu F, Jin D & Gui X, “Effect of blade sweep on inlet flow in axial compressor cascadesâ€, Chinese Journal of Aeronautics, Vol.28, No.1,(2015), pp.103-111.

      [12] Kim JH, Choi KJ & Kim KY, “Aerodynamic analysis and optimization of a transonic axial compressor with casing grooves to improve operating stabilityâ€, Aerospace Science and Technology, Vol.29, (2013), pp.81–91.

      [13] Bansal RK, “A Text Book of Fluid Mechanics and Hydraulic Machinesâ€,(2015).

      [14] Roy B, “Aircraft Propulsion-Science of making thrust to flyâ€, Published by Elsevier, (2008).

      [15] Sriniva G, Raghunandana K & Satish shenoy B, “Recent developments of axial flow compressor under transonic flow conditionsâ€, IOP conference series: Material Science and Engineering, (2017).

      [16] Reid L & Moore RD, “Design and overall performance of four highly-loaded, high-speed inlet stages for an advanced high-pressureratio core compressorâ€, NASA TP, (1978).

      [17] ANSYS ICEM CFD 17.0, 2017, User Manual.

      [18] Cadorin M, Morini M & Pinelli M, “Numerical Analyses of High Reynolds Number Flow of High Pressure Fuel Gas Through Rough Pipesâ€, International Journal of Hydrogen Energy, Vol.35, (2010), pp. 7568-7579

      [19] ANSYS CFX 11.0,User Manual.2007.

      [20] Apsley D, “CFD Calculation of Turbulent Flow with Arbitrary Wall Roughnessâ€, Flow, Turbulence and Combustion, (2007), pp. 153-175.

  • Downloads

  • How to Cite

    Srinivas, G., Raghunandana, K., & Satish Shenoy, B. (2018). Flow blockage in a transonic axial flow compressor: simulation analysis under distorted conditions. International Journal of Engineering & Technology, 7(2.21), 43-49. https://doi.org/10.14419/ijet.v7i2.21.11833

    Received date: 2018-04-21

    Accepted date: 2018-04-21

    Published date: 2018-04-20