Estimation of occupational safety risks at energetic sector of Iron and Steel Works

  • Authors

    • Volodymyr Kukhar
    • Nelly Yelistratova
    • Vadym Burko
    • Yulia Nizhelska
    • Olga Aksionova
    2018-04-20
    https://doi.org/10.14419/ijet.v7i2.23.11922
  • Industrial Injuries, Occupational Safety Studies, Technology Risk Assessment, Accident, International Standards.
  • Modern methods of estimation of working conditions at the metallurgical enterprise are considered on the occupational safety due to European standards. The main approaches are identified in determination of hazards at work, assessing of technological risks and injuries as an example for one of the Iron and Steel Works,Mariupol,Ukraine. The purpose of this work is to analyze the effectiveness of the introduction of international methods in the field of health safety, assess the effectiveness of the safety management system at an industrial enterprise. The analysis of the process of implementing European standards in the field of the health safety at industrial enterprises is a prerequisite for their further successful application, reducing the level of injuries. The procedures for drawing up the matrix of risk assessment (HAZID method), assessment of working capacity of technological processes (HAZOP method), and safety assessment of works (ISA method) are considered. The analysis of the efficiency of measures to increase of health safety in the energy (gas) sector at the enterprise was carried out. A graph of the dynamics of the decline in industrial injuries in five years is shown. The main statistical indicators that are used to account for industrial injuries at an industrial enterprise are given.

     

  • References

    1. [1] Abolfazl Ghahramani, and Heikki Summala, "A study of the effect of OHSAS 18001 on the occupational injury rate in Iran", International Journal of Injury Control and Safety Promotion, (2015), pp. 1-6, http://dx.doi.org/10.1080/17457300.2015.1088038.
      [2] Ligade, A.S., and Thalange, S.B., "Occupational health and safety management system (OHSMS) model for construction industry", IJRET: International Journal of Research in Engineering and Technology, IC-RICE Conference Issue, (2013), pp. 395-399.
      [3] Tine Herreborg J?rgensen, and Ole Busck, "Occupational health and safety regulation and management systems: experiences from Denmark", Division of Technology, Environment and Society, Department of Development and Planning, Aalborg University, Working Paper 8, (2004), pp. 1-11.
      [4] Jes?s ?lvarez-Santos, Josï¿©-?. Miguel-D?vila, Liliana Herrera, and Mariano Nieto, "Safety Management System in TQM environments", Safety Science, Vol. 101, (2018), pp. 135-143, http://dx.doi.org/10.1016/j.ssci.2017.08.019.
      [5] Berkhout, P.H.G., and Damen, M. "Estimating individual occupational risk using registration data", Safety Science, Vol. 82, (2016), pp. 95-102, http://dx.doi.org/10.1016/j.ssci.2015.08.013.
      [6] Kontogiannis, T., Leva, M.C., and Balfe, N., "Total Safety Management: Principles, processes and methods", Safety Science, Vol. 100, Part B, (2017), pp. 128-142, http://dx.doi.org/10.1016/j.ssci.2016.09.015.
      [7] Adel Badri, Andrï¿© Gbodossou, and Sylvie Nadeau, "Occupational health and safety risks: Towards the integration into project management", Safety Science, Vol. 50, Issue 2, (2012), pp. 190-198, http://dx.doi.org/10.1016/j.ssci.2011.08.008.
      [8] Beatriz Fern?ndez-Mu?iz, Josï¿© Manuel Montes-Pe?n, and Camilo Josï¿© V?zquez-Ord?s, "The role of safety leadership and working conditions in safety performance in process industries", Journal of Loss Prevention in the Process Industries, Vol. 50, Part B, (2017), pp. 403-415, http://dx.doi.org/10.1016/j.jlp.2017.11.001.
      [9] Fadwa Eljack, and Monzure-Khoda Kazi, "Process safety and abnormal situation management", Current Opinion in Chemical Engineering, Vol. 14, (2016), pp. 35-41, http://dx.doi.org/10.1016/j.coche.2016.07.004.
      [10] Vinodkumar, M.N., and Bhasi M., "Safety management practices and safety behaviour: Assessing the mediating role of safety knowledge and motivation", Accident Analysis & Prevention, Vol. 42, Issue 6, (2010), pp. 2082-2093, http://dx.doi.org/10.1016/j.aap.2010.06.021.
      [11] Vinodkumar, M.N., and Bhasi M., "A study on the impact of management system certification on safety management", Safety Science, Vol. 49, Issue 3, (2011), pp. 498-507, http://dx.doi.org/10.1016/j.ssci.2010.11.009.
      [12] Chinniah, Y., "Analysis and prevention of serious and fatal accidents related to moving parts of machinery", Safety Science, Vol. 75, (2015), pp. 163-173, http://dx.doi.org/10.1016/j.ssci.2015.02.004.
      [13] Lutsenko, I., Fomovskaya, E., Oksanych, I., Koval, S., and Serdiuk, O., "Development of a verification method of estimated indicators for their use as an optimization criterion", Eastern-European Journal of Enterprise Technologies, Vol. 2, No. 4 (86), (2017), pp. 17-23, http://dx.doi.org/10.15587/1729-4061.2017.95914.
      [14] Bogoliubov, V.M., Nagorniuk, O.M., and Sobczyk, W., "Providing environmental training in the context of Ukraine's transition to sustainable development", Annals of Agrarian Science, Vol. 14,
      Issue 4, (2016), pp. 292-294, http://dx.doi.org/10.1016/j.aasci.2016.09.003.
      [15] Manual for Occupational Safety in PJSC "ArcelorMittal Kryvyi Rih", Krivoi Roh, (2014), 74 p. (in rus.), available online: https://ukraine.arcelormittal.com/images/pdf/rukovodstvo_hs_2014.pdf.
      [16] Report on occupational safety of PJSC "ArcelorMittal Kryvyi Rih" for 2011, Krivoi Roh, (2011), 18 p. (in rus.), available online: https://ukraine.arcelormittal.com/images/pdf/H&S_Report_2011.pdf.
      [17] Kukhar, V., Balalayeva, E., and Nesterov, O., "Calculation Method and Simulation of Work of the Ring Elastic Compensator for Sheet-Forming", MATEC Web of Conferences, Vol. 129, (2017), 01041, http://dx.doi.org/10.1051/matecconf/201712901041.
      [18] Elena Balalayeva, Viktor Artiukh, Volodymyr Kukhar, Olga Tuzenko, Glazko Vladyslav, Andrii Prysiazhnyi, and Kankhva Vadim, "Researching of the Stress-Strain State of the Open-Type Press Frame Using of Elastic Compensator of Errors of "Press-Die" System", Advances in Intelligent Systems and Computing, Vol. 692, pp. 220-235, http://dx.doi.org/10.1007/978-3-319-70987-1_24.
      [19] Bogdan Paw?owski, Piotr Ba?a, Janusz Krawczyk, Milena St?pie?, and Tomasz ?leboda, "Failure analysis of shock absorber tubes", Engineering Failure Analysis, Vol. 82, (2017), pp. 533-539, http://dx.doi.org/10.1016/j.engfailanal.2017.04.009.
      [20] Kukhar, V.V., and Vasylevskyi, O.V. "Experimental research of distribution of strains and stresses in work-piece at different modes of stretch-forging with rotation in combined dies", Metallurgical and Mining Industry, No. 3, (2014), pp. 71-78, available online: http://www.metaljournal.com.ua/assets/ Archive/en/MMI3/14.pdf.
      [21] Grushko, A.V., Kukhar, V.V., and Slobodyanyuk, Yu.O., "Phenomenological Model of Low-Carbon Steels Hardening during Multistage Drawing", Solid State Phenomena, Vol. 265, (2017), pp. 114-123, http://dx.doi.org/10.4028/www.scientific.net/SSP.265.114.
      [22] Volodymyr Kukhar, Andrii Prysiazhnyi, Elena Balalayeva, and Oleksandr Anishchenko, "Designing of induction heaters for the edges of pre-rolled wide ultrafine sheets and strips correlated with the chilling end-effect", Modern Electrical and Energy System (MEES'2017), IEEE, Kremenchuk, Ukraine, (2017), pp. 404-407, http://dx.doi.org/10.1109/MEES.2017.8248945.
      [23] Volodymyr Kukhar, Victor Artiukh, Andrey Butyrin, and Andrii Prysiazhnyi, "Stress-Strain State and Plasticity Reserve Depletion on the Lateral Surface of Workpiece at Various Contact Conditions during Upsetting", Advances in Intelligent Systems and Computing, Vol. 692, (2018), pp. 201-211, http://dx.doi.org/10.1007/978-3-319-70987-1_22.
      [24] Albert Sesï¿©, Alfonso L. Palmer, Berta Cajal, Juan J. Monta?o, Rafael Jimï¿©nez, Noelia Llorens, "Occupational safety and health in Spain", Journal of Safety Research, Vol. 33, Issue 4, (2002), pp. 511-525, http://dx.doi.org/10.1016/S0022-4375(02)00054-3.
      [25] Danuta Koradecka, and Helena Dryzek, "Occupational safety and health in Poland", Journal of Safety Research, Vol. 32, Issue 2, (2001), pp. 187-208, http://dx.doi.org/10.1016/S0022-4375(01)00044-5.
      [26] Arquillos, A.L., Romero, J.C.R., Gibb, A., "Analysis of construction accidents in Spain, 2003-2008", Journal of Safety Research, Vol. 43, (2012), pp. 381-388, http://dx.doi.org/10.1016/j.jsr.2012.07.005.

      [27] Emma Maano Nghitanwa, and Lindiwe I Zungu, "Occupational health and safety provision awareness among construction workers on the construction industry of Windhoek, Namibia", International Journal of Health, Vol. 5, No. 1, (2017), pp. 60-63, http://dx.doi.org/10.14419/ijh.v5i1.7294.
      [28] Zeng, S.X., Tam, V.W.Y., and Tam, C. "Towards occupational health and safety systems in the construction industry of China", Safety Science, Vol. 46 (8), (2008), pp. 1155-1168, https://dx.doi.org/10.1016/j.ssci.2007.08.005.
      [29] Helena Ran?ngen, and Thomas Zobel, "Exploring the path from management systems to stakeholder management in the Swedish mining industry", Journal of Cleaner Production, Vol. 84, (2014), pp. 128-141, https://dx.doi.org/10.1016/j.jclepro.2014.04.025.
      [30] Kudryavtsev, Sergey S., Yemelin, Pavel V., and Yemelina Natalya K., "The Development of a Risk Management System in the Field of Industrial Safety in the Republic of Kazakhstan", Safety and Health at Work, (2017), http://dx.doi.org/10.1016/j.shaw.2017.06.003.
      [31] Nilgun Ulutasdemir, Metin Cirpan, Ebru Ozturk Copur, and Ferdi Tanir, "Occupational Risk of Health Professionals in Turkey a an Emerging Economy", Annals of Global Health, Vol. 81, No. 4, (2015), pp. 522-529, http://dx.doi.org/10.1016/j.aogh.2015.08.019.
      [32] Diana Maria Ceballos, and Zhao Dong, "The formal electronic recycling industry: Challenges and opportunities in occupational and environmental health research", Environment International,
      Vol. 95, (2016), pp. 157-166, https://dx.doi.org/10.1016/j.envint.2016.07.010.

  • Downloads

  • How to Cite

    Kukhar, V., Yelistratova, N., Burko, V., Nizhelska, Y., & Aksionova, O. (2018). Estimation of occupational safety risks at energetic sector of Iron and Steel Works. International Journal of Engineering & Technology, 7(2.23), 216-220. https://doi.org/10.14419/ijet.v7i2.23.11922