Using Simulation for Development of The Systems of Automobile Gas Diesel Engine and its Operation Control

  • Authors

    • Mikhail G. Shatrov
    • Vladimir V. Sinyavski
    • Andrey Yu. Dunin
    • Ivan G. Shishlov
    • Andrey V. Vakulenko
    • Andrey L. Yakovenko
    2018-05-16
    https://doi.org/10.14419/ijet.v7i2.28.12947
  • gas diesel engine, dual fuel engine, engine control system, gas feed system, diesel fuel system, injection rate shaping

  • Abstract

    The work was aimed at the development of gas supply, diesel fuel supply and electronic control systems for automobile gas diesel engines. Different ways of diesel engine conversion to operate on natural gas were analyzed. Gas diesel process with minimized ignition portion of diesel fuel injected by the CR system was selected. Electronic engine control and modular gas feed systems which can be used on high- and middle-speed gas diesel engines were developed. Diesel CR fuel supply system was developed in cooperation with the industrial partner. Simulation was used to obtain basic parameters and control methods of these systems. The base diesel engine was converted into gas diesel engine using the systems developed. Bench tests of the gas diesel engine demonstrated a high share of diesel fuel substitution with gas, high fuel efficiency and large decrease of NOх and СО2 emissions.

     

  • References

    1. [1] Markov VA, Gaivoronski AI, Grehov LV & Ivaschenko NA (2008), Operation of Diesel Engine on Non-Traditional Fuels. Legion-Avtodata, Moscow, 464 p.

      [2] Luksho VA, A Complex Method of Increasing Energy Efficiency of Gas Engines with High Compression Ratio and Shortened Intake and Exhaust Strokes, Ph.D. Thesis, NAMI, Moscow, 2015, 365 p.

      [3] Ivković IS, Kaplanović SM & Milovanović BM (2017), Influence of Road and Traffic Conditions on Fuel Consumption and Fuel Cost for Different Bus Technologies. Thermal Science, 21(1B), 693-706.

      [4] Geiger J, Heuser P, Lauer S, Huchtebrock B & Sankhla H (2013), Combustion System Development for a Large Bore Gas Engine – Efficient Combination of Simulation and Experiment. Paper no 80, 27th SIMAC Congress, Helsinki.

      [5] Klausner J, Lang J & Trapp C (2011), J624 - Der weltweit erste Gasmotor mit zweistufiger Aufladung, MTZ – Motortechnische Zeitschrift Ausgabe, Vol. 04.

      [6] Grotz M, Böwing R, Lang J, Thalhauser J, Christiner P & Wimmer A (2015), Efficiency Increase of a High Performance Gas Engine for Distributed Power Generation, 6th CIMAC Cascades. Dual Fuel and Gas Engines – Their Impact on Application, Design and Components.

      [7] Kudryavtzev A & Lomashov V (2010), Belaz Trucks of XXI Century with DM Family Gas Diesel Engines. AvtoGasoZapravochniy komplex + Alternatvnoye toplivo/AutoGasFillingComplex + Alternative Fuel, 3, 3-6.

      [8] Grehov LV, Ivaschenko NA & Markov VA (2010), On Ways to Improve the Gas Diesel Cycle. AvtoGasoZapravochniy komplex + Alternatvnoye toplivo/AutoGasFillingComplex + Alternative Fuel, 7(100), 10-14.

      [9] Mikulski M & Wierzbicki S (2017), Validation of a Zero-Dimensional and Two-Phase Combustion Model for Dual-Fuel Compression Ignition Engine Simulation. Thermal Science, 21(1B), 387-399.

      [10] Khatchijan AS, Sinyavskiy VV, Shishlov IG & Karpov DM (2010), Modeling of Parameters and Characteristics of Natural Gas Powered Engines. Transport na Alternativnom Toplive/Transport on Alternative Fuel, 3(15), 14-19.

      [11] Shatrov MG, Sinyavski VV, Dunin AY, Shishlov IG & Vakulenko AV (2017), Method of conversion of high- and middle-speed diesel engines into gas diesel engines. Facta Universitatis. Series: Mechanical Engineering, Vol. 15, No 3, 383-395.

      [12] Shatrov MG, Golubkov LN, Dunin AY, Yakovenko AL & Dushkin PV (2015), Influence of high injection pressure on fuel injection performances and diesel engine working process. Thermal Science, Vol. 19, No. 6, 2245-2253.

      [13] Shatrov MG, Golubkov LN, Dunin AY, Dushkin PV & Yakovenko AL (2017), A method of control of injection rate shape by acting upon electromagnetic control valve of common rail injector. International Journal of Mechanical Engineering and Technology, Vol. 8, Issue 11, 676-690.

      [14] Shatrov MG, Golubkov LN, Dunin AY, Dushkin PV & Yakovenko AL (2017), The new generation of common rail fuel injection system for Russian locomotive diesel engines. Pollution Research, Vol. 36 (3), 678-684.

      [15] Shatrov MG, Malchuk VI, Dunin AY & Yakovenko AL (2016), The influence of location of input edges of injection holes on hydraulic characteristics of injector the diesel fuel system. International Journal of Applied Engineering Research, Vol. 11, No. 20, 10267-10273.

      [16] Shatrov MG, Golubkov LN, Dunin AY, Yakovenko AL & Dushkin P.V (2016), Experimental research of hydrodynamic effects in common rail fuel system in case of multiple injection. International Journal of Applied Engineering Research, Vol. 11, No. 10, 6949-6953.

      [17] Sinyavski VV, Alekseev IV, Ivanov IY, Bogdanov SN & Trofimenko YV (2017), Physical simulation of high- and medium-speed engines powered by natural gas. Pollution Research, Vol. 36 (3), 684-690.

  • Downloads

  • How to Cite

    G. Shatrov, M., V. Sinyavski, V., Yu. Dunin, A., G. Shishlov, I., V. Vakulenko, A., & L. Yakovenko, A. (2018). Using Simulation for Development of The Systems of Automobile Gas Diesel Engine and its Operation Control. International Journal of Engineering & Technology, 7(2.28), 288-295. https://doi.org/10.14419/ijet.v7i2.28.12947

    Received date: 2018-05-17

    Accepted date: 2018-05-17

    Published date: 2018-05-16