Design and simulation of low actuation voltage RF MEMS shunt capacitive switch with serpentine flexures&rectangular perforations

  • Authors

    • K Jayavardhani
    • S K. Noureen Fathima
    • K Bhima Sankar
    • K Kavya Sri
    • S Sunithamani
    2018-05-29
    https://doi.org/10.14419/ijet.v7i2.31.13385
  • Actuation voltage, serpentine structure, MEMS switch, spring constant

  • Abstract

    This paper presents the design and simulation of RF MEMS shunt capacitive switch with low actuation voltage, low insertion loss and high isolation. Actuation voltage depends on the parameters like air gap, spring constant and actuation area. In this design, we have proposed a serpentine meander structure to reduce the spring constant of the beam thus reducing actuation voltage. The rectangular perforation is used to reduce the squeeze film damping by decreasing the mass of the switch. The proposed switch has attained a low actuation voltage of 4.5V for a displacement of 0.84μm. The air gap between the beam and the dielectric is 1μm. This radio frequency (RF) MEMS shunt switch is designed and simulated using COMSOL Multiphysics 5.2. The RF performance of the shunt switch is analyzed in Ansoft HFSS 13 and the results show that the return loss was about -13.50 dB at 20GHz in the OFF state and -8.5 dB at 18 GHz in the ON state. A high isolation of -36.00 dB was achieved in the OFF state at a frequency of 5GHz and a low insertion loss is obtained. The results show that the switch is suitable for wireless applications operating in the frequency range from 5 to 20GHz.

     

  • References

    1. [1] Rebeiz G, RF MEMS Theory, Design, and Technology, New York: Wiley, (2003).

      [2] Persano A, Cola A, De Angelis G, Taurino A, Siciliano P & Quaranta F, “Capacitive RF MEMS switches with tantalum-based materialsâ€, J. Microelectromech. Syst., Vol.20, No.2, (2011), pp.365–370, 2011.

      [3] Shekhar S & Vinoy KJ, “Surface-Micromachined capacitive RF Switches with low actuation voltage and steady contactâ€, Journal of Microelectromechanical systems, (2017).

      [4] Saffari H, Moghadam RA & Tahmasebipour M, “Low actuation voltage RF MEMS Shunt Capacitive Switch based on rotated serpentine springâ€, Iranian Conference on Electrical Engineering (ICEE), (2017), pp.293-297.

      [5] Saxena A & Agrawal VK, “Comparative study of perforated RF MEMS Switchâ€, 3rd International Conference on Recent Trends in Computing, (2015).

      [6] Chaurasia AK & Mehra R, “Design and Performance Analysis of Capacitive RF MEMS Switch for Low Voltage Reconfigurable Antennasâ€, International Journal of IT, Engineering and Applied Sciences Research (IJIEASR), Vol.3, No.9, (2014).

      [7] Balaji K & Baranichandar K, “Design and Analysis of MEMS Switch for RF Applicationsâ€, International Journal of scientific research and management (IJSRM), Vol.3, No.1, (2015).

      [8] Rebeiz GM, “RF MEMS Switches: Status of the Technologyâ€, International conference on solid state sensors, Actuators and microsystems, (2003).

      [9] Lakshmi Narayana T, GirijaSravani K & Srinivasa Rao K, “Design and analysis of CPW based shunt capacitive RF MEMS switchâ€, Cogent Engineering, Vol.4, No.1, (2017).

      [10] Saxena A & Agrawal VK, “RF MEMS Perforated Shunt Switch Design on Hafnium Oxide Substrate for Low Actuation Voltageâ€, International Journal of Electronics and Electrical Engineering, Vol. 4, No. 6, (2016).

      [11] Kulkarni SG, “A Novel Design of Cantilever RF MEMS Series Switchâ€, IOSR Journal of Electronics and Communication Engineering (IOSR-JECE), Vol.10, No.3, (2015).

      [12] Kaur R, Tripathi CC & Kumar D, “Low Voltage Rf Mems Capacitive Shunt Switchesâ€, Wireless PersCommun, Vol.78,(2014), pp.1391–1401.

      [13] Peroulis D, Pacheco SP, Sarabandi K & Katehi LP, “Electromechanical considerations in developing low-voltage RF MEMS switchesâ€, IEEE Transactions on microwave theory and techniques, Vol.51, No.1,(2003), pp.259-270.

      [14] Sharma A, Shah A & Bharti R, “Design & Simulation of Low Actuation Voltage Perforated Shunt RF MEMS Switchâ€, International Journal of Engineering and Technical Research (IJETR), Vol.3, No.6, (2015).

      [15] Manivannan M, JosephDaniel R & Sumangala K, “Low Actuation Voltage RF MEMS Swi tch Using Varying Section Composite Fixed-Fixed Beamâ€, International Journal of Microwave Science and Technology, (2014).

      [16] Molaei S & Ganji BA, “Design and simulation of a novel RF MEMS shunt capacitive switch with low actuation voltage and high isolationâ€, Microsystem Technologies, Vol.23, No.6,(2017), pp.1907-1912.

      [17] Rao KS, Prakash MD & Thalluri LN, “Cantilever and circular disc structure based capacitive shunt RF MEMS switchesâ€, International Conference on Electrical, Electronics, Communication, Computer and Optimization Techniques (ICEECCOT), (2016), pp.336-338.

      [18] Sarkar S & Vimala Juliet A, “Design of a Low Voltage RF MEMS Capacitive Switch with Low Spring Constantâ€, International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering, Vol.3, No.4, (2014).

      [19] Raman R, Shanmuganantham T & Sindhanaiselvi D, “Analysis of RF MEMS Series Switch with Serpentine Spring Shaped Cantilever Beam for Wireless Applicationsâ€, PMME, (2016).

      [20] Singh T, Khaira N & Sengar J, “A novel capacitive RF MEMS switch design for low voltage applicationsâ€, Fourth International Conference on Computing, Communications and Networking Technologies (ICCCNT), (2013), pp.1-6.

      [21] Rebeiz GM & Muldavin JB, “RF MEMS switches and switch circuitsâ€, IEEE Microwave magazine, Vol.2, No.4,(2001), pp.59-71.

  • Downloads

  • How to Cite

    Jayavardhani, K., K. Noureen Fathima, S., Bhima Sankar, K., Kavya Sri, K., & Sunithamani, S. (2018). Design and simulation of low actuation voltage RF MEMS shunt capacitive switch with serpentine flexures&rectangular perforations. International Journal of Engineering & Technology, 7(2.31), 4-8. https://doi.org/10.14419/ijet.v7i2.31.13385

    Received date: 2018-05-28

    Accepted date: 2018-05-28

    Published date: 2018-05-29