Profile of cold-formed steel for compression member design a basic combination performance

  • Authors

    • Zamzami Septiropa Universiti Tenaga Nasional
    • Mohd. Hanim Osman
    • Ahmad Baharuddin Abd. Rahman
    • Mohd. Azreen Mohd Ariffin
    • Miftachul Huda
    • Andino Maseleno
    2018-08-23
    https://doi.org/10.14419/ijet.v7i2.27.15807
  • Cold-Formed Steel, Combine Profiles, Column.

  • Abstract

    Experiment previously showed several findings that the strength of cold-formed steel cross-section are not the same, where web strength and flange strength do not give the same response when receiving the axial load. This occurs not only because of a shift in the center point of the force due to deformation of the cross section, but also due to different strengths in cross-section, especially on the web section and flange section. To find out more details of this case, the experiment carried out the tensile test for mechanics property and compression test with an axial load to find which parts are weaknesses, then used as a reference in combining the profile. The compression test results showed significant increase in compression capability between single profile with double profile back to back (Dbb) or double profile flange to flange (Dff) with ratio 1: 2.24 and 1: 2.44 respectively. There is a non-linear increase in the value of Aeff and Ieff when becomes combine profiles (double, quadruple, hexatruple), so this can be the basis for increasing the combine profile capacity to be able to withstand larger loads. This experiment can show a basic performance of CFS, where are weak section parts of a profile can be used as a reference to put combine profile to increase compression capacity. With a numerical analysis approach compared to the experimental results, the combination of Cold-formed steel profile is established as a column for the low-rise building structure.

     

     

  • References

    1. [1] M. Dabaon, E. Ellobody, and K. Ramzy, "Nonlinear behaviour of built-up cold-formed steel section battened columns," Journal of Constructional Steel Research, vol. 110, pp. 16-28, 2015. https://doi.org/10.1016/j.jcsr.2015.03.007.

      [2] P. B. Dinis and D. Camotim, "Cold-formed steel columns undergoing local–distortional coupling: Behaviour and direct strength prediction against interactive failure," Computers & Structures, vol. 147, pp. 181-208, 2015. https://doi.org/10.1016/j.compstruc.2014.09.012.

      [3] Y. Huang and B. Young, "Structural performance of cold-formed lean duplex stainless steel columns," Thin-Walled Structures, vol. 83, pp. 59-69, 2014. https://doi.org/10.1016/j.tws.2014.01.006.

      [4] S. Gunalan, Y. B. Heva, and M. Mahendran, "Flexural–torsional buckling behaviour and design of cold-formed steel compression members at elevated temperatures," Engineering Structures, vol. 79, pp. 149-168, 2014. https://doi.org/10.1016/j.engstruct.2014.07.036.

      [5] . Dabaon, E. Ellobody, and K. Ramzy, "Experimental investigation of built-up cold-formed steel section battened columns," Thin-Walled Structures, vol. 92, pp. 137-145, 2015. https://doi.org/10.1016/j.tws.2015.03.001.

      [6] ASTM, "Standard Test Methods for Tension Testing of Metallic Materials," vol. Designation: E8/E8M − 15a, ed: ASTM, 2013, p. 29.

      [7] A. E8-01, "Standard Test Methods for Tension Testing of Metallic Materials," in Tention Testing of metallic material (sheet metal) vol. E 8 - 01, ed: American Association State Highway and Transportation Officials Standard AASHTO No.: T68 An American National Standard, 2013, p. 22.

      [8] Y. W. W, "Cold-formed steel structures†in Structure Engineering Handbook, C. Wai-Fah, Ed., ed: Boca Raton: CRC Press LLC, 1999, 1999.

      [9] M. Chen and B. F. Deng, "Analysis on Bearing Capacity of Axial Compression Short Column of Double Back-to-Back C Steel with Gusset Plates," Applied Mechanics and Materials, vol. 501-504, pp. 523-526, 2014. https://doi.org/10.4028/www.scientific.net/AMM.501-504.523.

      [10] S. N. Sreedhar Kalavagunta, Kamal Nasharuddin Bin Mustapha, "Experimental Study of Axially Compressed Cold Formed Steel Channel Column," Indian Journal of Science and technology, vol. 06 (04) April 2013 2013.

      [11] A. D. Martins, D. Camotim, P. B. Dinis, and B. Young, "Local–Distortional Interaction in Cold-formed Steel Columns: Mechanics, Testing, Numerical Simulation and Design," Structures, vol. 4, pp. 38-57, 2015. https://doi.org/10.1016/j.istruc.2015.10.005.

      [12] E. C. f. S. Eurocode-3, Eurocode 3 Design of steel structure part 1-3 (BS EN 1993-1-3-2006) vol. EN 1993 - 1 - 3 British Stndard, 2006.

      [13] A. N. 2005, ASNZS 4600-2005 ColdFormed Steel Structure. Australia: Standards Australia Limited/Standards New Zealand, 2005.

      [14] Huda, M. (2018). Empowering Application Strategy in the Technology Adoption: Insights from Professional and Ethical Engagement. Journal of Science and Technology Policy Management. https://doi.org/10.1108/JSTPM-09-2017-0044.

      [15] Adela, A., Jasmi, K.A., Basiron, B., Huda, M., Maseleno, A. (2018). Selection of dancer member using simple additive weighting. International Journal of Engineering & Technology. 7(3). 1096-1107. https://doi.org/10.14419/ijet.v7i3.11983 ...

      [16] Amin, M.M., Nugratama, M.A.A., Maseleno, A., Huda, M., Jasmi, K.A., (2018). Design of cigarette disposal blower and automatic freshner using mq-5 sensor based on atmega 8535 microcontroller. International Journal of Engineering & Technology. 7(3). 1108-1113. https://doi.org/10.14419/ijet.v7i3.11917.

      [17] Assahubulkahfi, M., Sam, Y.M., Maseleno, A., Huda, M. (2018). LQR Tuning by Particle Swarm Optimization of Full Car Suspension System. International Journal of Engineering & Technology. 7 (2.13), 328-331.

      [18] Kurniasih, D., Jasmi, K.A., Basiron, B., Huda, M., Maseleno, A. (2018). The uses of fuzzy logic method for finding agriculture and livestock value of potential village. International Journal of Engineering & Technology. 7(3). 1091-1095. https://doi.org/10.14419/ijet.v7i3.11984.

      [19] Kurniasih, D., Jasmi, K.A., Basiron, B., Huda, M., Maseleno, A. (2018). The uses of fuzzy logic method for finding agriculture and livestock value of potential village. International Journal of Engineering & Technology. 7(3). 1091-1095. https://doi.org/10.14419/ijet.v7i3.11984.

      [20] Maseleno, A., Pardimin, Huda, M., Ramlan, Hehsan, A., Yusof, Y.M., Haron, Z., Ripin, M.N., nor, N.H.M., and Junaidi, J. (2018a). Mathematical Theory of Evidence to Subject Expertise Diagnostic. ICIC Express Letters, 12 (4), 369 DOI: 10.24507/icicel.12.04.369

      [21] Maseleno, A., Huda, M., Jasmi, K.A., Basiron, B., Mustari, I., Don, A.G., and Ahmad, R. (2018b). Hau-Kashyap approach for student’s level of expertise. Egyptian Informatics Journal, https://doi.org/10.1016/j.eij.2018.04.001.

      [22] Maseleno, A., Sabani, N., Huda, M., Ahmad, R., Jasmi, K.A., Basiron, B. (2018c). Demystifying Learning Analytics in Personalised Learning. International Journal of Engineering & Technology. 7(3). 1124-1129. https://doi.org/10.14419/ijet.v7i3.9789.

      [23] Moksin, A. I., Shahrill, M., Anshari, M., Huda, M., & Tengah, K. A. (2018b). The Learning of Integration in Calculus Using the Autograph Technology. Advanced Science Letters, 24(1), 550-552. https://doi.org/10.1166/asl.2018.12067.

      [24] Putra, D.A.D., Jasmi, K.A., Basiron, B., Huda, M., Maseleno, A., Shankar, K., Aminudin, N. (2018). Tactical Steps for E-Government Development. International Journal of Pure and Applied Mathematics.119 (15). 2251-2258.

      [25] Rosli, M.R.B., Salamon, H.B., and Huda, M. (2018). Distribution Management of Zakat Fund: Recommended Proposal for Asnaf Riqab in Malaysia. International Journal of Civil Engineering and Technology 9(3), pp. 56–64.

      [26] Sugiyarti, E., Jasmi, K.A., Basiron, B., Huda, M., Shankar, K., Maseleno, A. (2018). Decision support system of scholarship grantee selection using data mining. International Journal of Pure and Applied Mathematics.119 (15), 2239-2249.

      [27] Sundari, E., Jasmi, K.A., Basiron, B., Huda, M., and Maseleno, A. (2018). Web-Based Decision Making System for Assessment of Employee Revenue using Weighted Product. International Journal of Engineering and Technology.

      [28] Susilowati, T., Jasmi, K.A., Basiron, B., Huda, M., Shankar, K., Maseleno, A., Julia, A., Sucipto. (2018). Determination of Scholarship Recipients Using Simple Additive Weighting Method. International Journal of Pure and Applied Mathematics.119 (15), 2231-2238.

  • Downloads

  • How to Cite

    Septiropa, Z., Hanim Osman, M., Baharuddin Abd. Rahman, A., Azreen Mohd Ariffin, M., Huda, M., & Maseleno, A. (2018). Profile of cold-formed steel for compression member design a basic combination performance. International Journal of Engineering & Technology, 7(2.27), 284-290. https://doi.org/10.14419/ijet.v7i2.27.15807

    Received date: 2018-07-18

    Accepted date: 2018-07-18

    Published date: 2018-08-23