Spray Characteristics and Internal Flow Structures of Swirl Effervescent Atomizer

  • Authors

    • Z A. Ghaffar
    • S Kasolang
    • Ahmad H. A. Hamid
    2018-07-21
    https://doi.org/10.14419/ijet.v7i3.11.15930
  • Swirl Effervescent Atomizer, Spray Characteristics, Internal Flow Structures, Shadowgraph.
  • Spray characteristics and internal flow structures of an atomizer are important parameters in indicating their performances. Both parameters are affected by the operating conditions and atomizer geometries. This study investigates the effect of operating parameters and atomizer geometries on spray angle, breakup length and gas core diameter of swirl effervescent atomizer. This work is conducted specifically to find the most critical parameters that will produce the required spray characteristics and internal flow structure. The atomizer performance tests were carried out using water as the working fluid and nitrogen gas as the atomizing agent. High-speed shadowgraph technique was utilized to record the videos of the spray and internal flow structures. The video recordings were converted to image sequences and analyzed using image processing software. Geometrical parameters were found to be more dominant for characterizing the resultant sprays, but operating conditions was more critical in affecting the internal flow structures. The widest spray angle (~25°) and shortest breakup length (~10mm) were observed at the high level of swirl-generating vane angle and discharge orifice diameter. Gas core diameter expanded up to 1.13mm at the high level of GLR.

     

     

  • References

    1. [1] S. D. Sovani, E. Chou, P. E. Sojka, J. P. Gore, W. A. Eckerle, and J. D. Crofts, High pressure effervescent atomization: effect of ambient pressure on spray cone angle, Fuel 80:3 (2001) 427–435.

      [2] J. Jedelsky and M. Jicha, Novel modifications of twin-fluid atomizers: performance, advantages and drawbacks, in 23th European Conference on Liquid Atomization and Spray Systems ILASS-Europe, Brno, Czech Republic, 6:8 (2010) 1–5.

      [3] M. Ochowiak, L. Broniarz-Press, S. Rozanska, M. Matuszak, and S. Wlodarczak, Characteristics of spray angle for effervescent-swirl atomizers, Chemical Engineering Process: Process Intensification 98 (2015) 52–59.

      [4] M. Ochowiak and M. Matuszak, The effect of additional aeration of liquid on the atomization process for a pneumatic nebulizer, European Journal of Pharmaceutical Sciences 97 (2017) 99–105.

      [5] X. Huang, X. Wang, and G. Liao, Visualization of two phase flow inside an effervescent atomizer, Journal of Visualization 11:4 (2008) 299–308.

      [6] B. J. Rho, S. J. Kang, J. H. Oh, and S. G. Lee, Swirl effect on the spray characteristics of a twin-fluid jet, KSME International Journal, 12:5 (1998) 899–906.

      [7] Z. A. Ghaffar, S. Kasolang, A. H. A. Hamid, M. A. A. Bakar, and C. S. Ow, Effect of Geometrical Parameters Interaction on Swirl Effervescent Atomizer Spray Angle, Jurnal Teknologi 76:9 (2015) 63–67.

      [8] M. Zaremba, L. Weiß, M. Malý, M. Wensing, J. Jedelský, and M. Jícha, Low-pressure twin-fluid atomization: Effect of mixing process on spray formation, International Journal of Multiphase Flow 89 (2017) 277–289.

      [9] Hedland, MR Flow Transmitter Installations and Programming Instructions, HLIT 306 (2008).

      [10] Z. A. Ghaffar, S. Kasolang, and A. H. A. Hamid, Characteristics of swirl effervescent atomizer spray angle, 607 (2014).

      [11] Z. A. Ghaffar, S. Kasolang, A. H. A. Hamid, C. S. Ow, and N. R. Nik Roselina, Design, development and performance evaluation of new swirl effervescent injector, Jurnal Teknologi, 75:1 (2015).

      [12] Z. A. Ghaffar, S. Kasolang, A. H. A. Hamid, A. Diyar I., K. I. Sainan, and N. R. Nik Roselina, Gas Core Characteristics of Swirl Effervescent Atomizer, Jurnal Teknologi, 76:9 (2015) 57–62.

      [13] V. Yang, M. Habiballah, J. Hulka, and M. Popp, Liquid rocket thrust chambers: aspects of modeling, analysis, and design, Progress in Astronautics and Aeronautics, 2004.

      [14] L. Juslin, O. Antikainen, P. Merkku, and J. Yliruusi, Droplet size measurement: I. Effect of three independent variables on droplet size distribution and spray angle from a pneumatic nozzle, International Journal of Pharmaceutics 123:2 (1995) 247–256.

      [15] G. N. Laryea and S. Y. No, Spray angle and breakup length of charge-injected electrostatic pressure-swirl nozzle, Journal of Electrostatics, 60:1 (2004) 37–47.

  • Downloads

  • How to Cite

    A. Ghaffar, Z., Kasolang, S., & H. A. Hamid, A. (2018). Spray Characteristics and Internal Flow Structures of Swirl Effervescent Atomizer. International Journal of Engineering & Technology, 7(3.11), 58-61. https://doi.org/10.14419/ijet.v7i3.11.15930