Flexural Behavior of Rolled Steel I Beam with Different Stiffener Position

  • Authors

    • Prabha. G
    • Emilreyan R
    2018-09-22
    https://doi.org/10.14419/ijet.v7i4.2.19992
  • Horizontal and vertical stiffener, Rolled steel section, Inclined stiffener, Flexural strength, etc..

  • Abstract

    Economy, ease and speed of construction are the main factors for using steel as a building material. In this paper conventional hot rolled steel I-beam sections are considered as the main flexural member of industrial buildings. The main goal is to increase the load carrying capacity of the beam with inverted w shape stiffener condition at centre. The initiative was to identify the maximum load behaviour and deflection of steel beams with stiffener in the web. The performance of such beams has been considered only for vertical loads. Hot rolled steel beam of ISMB 100 with stiffener were tested to failure experimentally. The beams were simply supported at the ends and subjected to a 2 equal concentrated load applied at one third of span from both ends.  The deflection at centre of beam and various failure patterns are studied. All the beams were analyzed by the finite element method by using general finite element analysis software ANSYS and the results were compared with those obtained experimentally. The finite element results for deformation and ultimate strength shows good agreement with the corresponding values observed in the experiments. At last, a comparative study was carried out using finite element method to examine that which type of beam gives best performance during loading. The numerical results indicate that the use of hot rolled I section with stiffener is an economical and advantageous choice.

     

  • References

    1. [1] Dewolf tj, pekoz t, winter g. Local and overall buckling of cold-formed members. Journal of structural engineering, asce, no. 10, 100(1974) 2017-36.

      [2] Beshara b, lawson tj. Built-up girder screw connection variation flexural tests, dietrich design group internal report, april, 2002.

      [3] Yu c, schafer bw, local buckling tests on cold-formed steel beams, journal of structural engineering, asce, 129(2003) 1596-606.

      [4] Serrette rl, performance of edge-loaded cold formed steel built-up box beams, journal of structural engineering, asce, no. 3, 9(2004) 170-4.

      [5] Ren w, fang s, young b, finite-element simulation and design of cold-formed steel channels subjected to web crippling, journal of structural engineering, asce, no. 12, 132(2006) 1967-75.

      [6] Akay, h.v., johnson c.p. And will k.m. (1977), lateral and local buckling of beams and frames, journal of structural engineering, asce, vol. 103, no. St9, sept., pp. 1821-1832.

      [7] Avery p. (1994) lateral distortional buckling behaviour of hollow flange beams with web stiffeners, beng thesis, queensland university of technology, australia.

      [8] Avery p. And mahendran, m. (1996), finite element analysis of hollow flange beams with web stiffeners, research report, queensland university of technology.

      [9] Bradford, m.a. And trahair, n.s. (1981), distortional buckling of i-beams, journal of structural engineering, asce, vol. 107, no. St2, pp. 355-370.

      [10] dempsey, r.i. (1991), hollow flange beams: the new alternative, technical presentation, aisc,june.

      [11] dempsey r.i. (1990), structural behaviour and design of hollow flange beams, proc. Of the second national structural engineering conference

      [12] Richard redwood and sevak demirdjian “castellated beam web buckling in shear†journal of structural engineering 1 october 1998/1207

      [13] Redwood, r. & demirdjian, s. (1998). Castellated beam web buckling in shear. Journal of structural engineering (asce), vol. 124, 10, pp. 1202-1207.

      [14] Sweedan m. I. (2011). Elastic lateral stability of i-shaped cellular steel beams. Journal of constructional steel research, vol. 67, no. 2, pp. 151-163.

      [15] Konstantinos, t. D. & mello, c. (2011). Web buckling study of the behavior and strength of perforated steel beam with different novel web opening shapes. Journal of constructional steel research, vol. 67, pp. 1605- 1620 6

      [16] Luis laim, joao paulo c rodrigues, luis s silva, “flexural behaviour of cold formed steel beamsâ€, dfe 2013- international conference on design, fabrication and economy of metal structures, (isbn: 978-3-642-36690-19), hungary

      [17] Jia-hui zhang, ben young, “compression test of cold- formed steel i-shaped open sections with edge and web stiffenersâ€, thinwalled structures 52 (2012) 1-11

      [18] Rajesh kumar b, anil kumar patidar and helen santhi. M, “finite element analysis of concrete filled cold formed steel sections using ansysâ€, ijace, vol no: 1, 2013, pp. 11-18

      [19] Sudha.k , sukumar.s , behaviour of cold-formed steel builtup i section under bending , international journal of engineering and technology (ijet) vol no: 5, 2013 pp 4622-4631

      [20] IS 800-2007 code of practice for general construction in steel.

  • Downloads

  • How to Cite

    G, P., & R, E. (2018). Flexural Behavior of Rolled Steel I Beam with Different Stiffener Position. International Journal of Engineering & Technology, 7(4.2), 10-14. https://doi.org/10.14419/ijet.v7i4.2.19992

    Received date: 2018-09-21

    Accepted date: 2018-09-21

    Published date: 2018-09-22