Open Architecture Control for CNC System – An Approach

  • Authors

    • Amit M. Mankar
    • R. L. Shrivastava
    • Jayant P. Giri
    2018-09-22
    https://doi.org/10.14419/ijet.v7i4.5.20034
  • CNC, Open Architecture Control, MATLAB/SIMULINK.

  • Abstract

    The Open Architecture concept is gaining more attention because of growing demand from end users. Numerical Control systems are limited in terms of portability because they are dependent on vendor-specific environment, to overcome this limitation Open Architecture Control was introduced. Open Architecture improves portability, interoperability, scalability and ability to reconfigure of an existing CNC machine. Open control system increases the flexibility of CNC machine by allowing vendor-neutral environment. Open Architecture Controller allows the end user to modify the existing system by integrating components from different manufacturers which reduce cost as well as increase extendibility of the system. In this review paper, different initiatives and developments on Open Architecture Controller are presented. This paper also covers the approaches made by researchers in the field of simulation of table movement in CNC machine.

     

     

  • References

    1. [1] MA Xiong-bo, HAN Zhen-yu, WANG Yong-zhang, FU Hong-ya.: Development of a PC-based Open Architecture Software-CNC System, Chinese Journal of Aeronautics 20272-281, Elsevier 272--281 (2007)

      [2] R. Ramesh, S. Jyothirmai, K. Lavanya.: Intelligent automation of design and manufacturing in machine tools using an open architecture motion controller, Journal of Manufacturing Systems 32, 248--259, Science Direct, Elsevier (2013)

      [3] Jorge Correa, Nicholas Toombs, Placid M. Ferreira.: Implementation Of An Open-Architecture Control For Cnc Systems Based On Open-Source Electronics, Proceedings of the ASME International Mechanical Engineering Congress and Exposition, ASME (2016)

      [4] Kamran Latif, YusriYusof.: New Method for the Development of Sustainable STEP-Compliant Open CNC System, Procedia CIRP, 40: 230--235, ScienceDirect, Elsevier (2016)

      [5] Beibei Li, Hun Lin, Liaomo Zheng, Shujie Sun, Zhenyu Yin.: An Open CNC System based on EtherCAT Network, 795--801, IEEE (2016)

      [6] Jiewen Wu, Di Li, Shiyong Wang.: The design and experimental research of an open architecture soft-CNC system based on RTX and an IPC, Springer (2016)

      [7] Gabriel S. Racz, Radu E. Breaz, Octavian C. Bologa, Valentin S. Oleksik.: Computer Simulation for the Study of CNC Feed Drives Dynamic Behavior and Accuracy, 2229--2233, EUROCON, IEEE (2007)

      [8] XU Wei, CHEN Jihong, YANG Jin: Design of servo system for 3-Axis CNC drilling machine based on xpc target, 447--450, IEEE (2009)

      [9] M. Ebrahimi, R. Whalley.: Analysis, modelling and simulation of stiffness in machine tool drives, computers & industrial engineering 38, 93--105, ELSEVIER (2000)

      [10] Gunter Pritschow, Yusuf Altintas, Francesco Jovane, YoramKoren, Mamoru Mitsuishi, ShozoTakata, Hendrik van Brussel, Manfred Weck, Kazuo Yamazaki.: Open controller architecture-past, present and future, CIRP Annals--Manufacturing Technology; 50(2): 463--470 (2001)

      [11] Sergej N. Grigoriev, Georgi M. Martinov.: Research and development of a cross-platform CNC kernel for multi-axis machine tool, 517--522, ELSEVIER (2014)

  • Downloads

  • How to Cite

    M. Mankar, A., L. Shrivastava, R., & P. Giri, J. (2018). Open Architecture Control for CNC System – An Approach. International Journal of Engineering & Technology, 7(4.5), 155-158. https://doi.org/10.14419/ijet.v7i4.5.20034

    Received date: 2018-09-22

    Accepted date: 2018-09-22

    Published date: 2018-09-22