Fire behavioural and mechanical properties of carbon fibre reinforced aluminium laminate composites for aero-engine

  • Authors

    • Ibrahim Mohammed
    • Abd Rahim Abu Talib
    • Mohamed Thariq Hameed Sultan3
    • Syamimi Sadoon
    2018-10-09
    https://doi.org/10.14419/ijet.v7i4.13.21323
  • composite, fibre metal laminate, fire designated zone, high temperature, mechanical properties.

  • Abstract

    Two different properties of fibre-metal laminate composites (FML), including the fire behaviour and mechanical properties, were experimentally studied in this paper. The fibre-metal laminate composites studied were made of aluminium alloy 2024-T3, carbon fibre, flax, kenaf and epoxy resin/hardener arranged in different forms. The aims of the study are to assess the fire behaviour of the composites using ISO2685 standard and mechanical properties of the composite after withstanding the burn-through according to the standard. The fire test was carried out using ISO2685 standard using a propane-air burner, whereby the propane gas and air serves as the fluid to the system. The universal testing machine of the 100 kN load cell and gun tunnel were used for the mechanical properties test according to each test standard. The fire results showed that three of the FML composites considered in the study are fireproof composites while carbon fibre kenaf reinforced aluminium laminate (CARALL4) is a fire resistant composite. Carbon fibre reinforced aluminium laminate with aluminium alloy at the front and the rear face (CARALL2) withstood higher flame temperature than the other FML composites with 14.4%, 49.0% and 82.8% greater than CARALL1, CARALL3 and CARALL4 in terms of thermal conductivity. In terms of mechanical properties, it was also CARALL2 that has higher tensile, compressive, flexural and impact strength. Therefore, the study showed that carbon fibre flax reinforced aluminium laminate (CARALL3) which is the hybrid composite with green fibre can compete with fibre-metal laminate composites of pure synthetic fibre in terms of their properties.

     

     

  • References

    1. [1] Mohammed I, Abu Talib AR, Sultan MTH & Saadon S (2018), Thermal properties of fibre-metal laminates composites. International Journal of Mechanical and Production Engineering Research and Development

      [2] Alderliesten R & Benedictus R (2008), Fiber/metal composite technology for future primary aircraft structures. Journal of Aircraft 45(4), 1182-1189

      [3] Beumler T, Pellenkoft F, Tillich A, Wohlers W & Smart C (2006), Airbus costumer benefit from fiber metal laminates. Airbus Deutschland GmbH

      [4] Chang P-Y, Yeh P-C & Yang J-M (2008), Fatigue crack initiation in hybrid boron/glass/aluminum fiber metal laminates. Materials Science and Engineering: A 496 (1), 273-280

      [5] Cortes P & Cantwell W (2006), The prediction of tensile failure in titanium-based thermoplastic fibre–metal laminates. Composites Science and Technology 66(13), 2306-2316

      [6] Homan J (2006), Fatigue initiation in fibre metal laminates. International Journal of Fatigue 28(4), 366-374

      [7] Skhabovskyi I, Batista NL, Damato CA, Reis RP, Botelho EC & Scotti A (2017), Appraisal of fiber-metal laminate panels reinforced with metal pins deposited by CMT welding. Composite Structures 180, 263-275

      [8] Vogelesang L & Vlot A (2000), Development of fibre metal laminates for advanced aerospace structures. Journal of Materials Processing Technology 103(1), 1-5

      [9] Mohammed I, Abu Talib AR, Sultan MTH & Saadon S (2017), Ballistic impact velocity response of carbon fibre reinforced aluminium alloy laminates for aero-engine. IOP Conference Series: Materials Science and Engineering 270, 012026

      [10] Fan J, Guan Z & Cantwell WJ (2011), Modeling perforation in glass fiber reinforced composites subjected to low velocity impact loading. Polymer Composites 32(9), 1380-1388

      [11] Jumahat A, Kasolang S & Bahari M (2015), Wear properties of nanosilica filled epoxy polymers and FRP composites. Jurnal Tribologi 6, 24-36

      [12] Sadighi M, Alderliesten R & Benedictus R (2012), Impact resistance of fiber-metal laminates: a review. International Journal of Impact Engineering 49, 77-90

      [13] Strong AB (2008), Fundamentals of composites manufacturing: materials, methods and applications. Society of Manufacturing Engineers

      [14] Asundi A & Choi AY (1997), Fiber metal laminates: an advanced material for future aircraft. Journal of Materials Processing Technology 63(1-3), 384-394

      [15] Mohammed I, Abu Talib AR, Sultan MTH, Jawaid M, Ariffin AH & Saadon S (2018), Mechanical properties of fibre-metal laminates made of natural/synthetic fibre composites. BioResources 13(1), 2022-2034

      [16] Sriramkumar J (2014), Mixture of alloys used for building a regenerator to bring down the temperature of liquid hydrogen (Lh2) below 20k. International Review of Applied Engineering Research 4(1), 47-56

      [17] Lawcock G, Ye L, Mai Y & Sun C (1998), Effects of fibre/matrix adhesion on carbon-fibre-reinforced metal laminates. Composites Science and Technology 57(2), 1609-1619

      [18] Vlot A & Gunnink JW (2011), Fibre metal laminates: an introduction. Springer Science & Business Media

      [19] Sivakumar D, Ng L & Selamat MZ (2017), Investigation on fatigue life behaviour of sustainable bio-based fibre metal laminate. Journal of Mechanical Engineering SI(1), 123-140

      [20] Tamilarasan U, Karunamoorthy L & Palanikumar K (2015), Mechanical properties evaluation of the carbon fibre reinforced aluminium sandwich composites. Materials Research 18(5),1029-1037

      [21] Rajkumar G, Krishna M, Murthy H, Sharma S & Mahesh K (2012), Investigation of repeated low velocity impact behaviour of GFRP / Aluminium and CFRP / Aluminium laminates. Int J Soft Comput Eng 1(6), 50-58

      [22] Sinmazçelik T, Avcu E, Bora MÖ & Çoban O (2011), A review: Fibre metal laminates, background, bonding types and applied test methods. Materials & Design 32(7), 3671-3685

      [23] Xia Y, Wang Y, Zhou Y & Jeelani S (2007), Effect of strain rate on tensile behavior of carbon fiber reinforced aluminum laminates. Materials Letters 61(1), 213-215

      [24] Neely A, Abu Talib AR, Ireland P & Mullender A (2000), Development of low-temperature fire-event modelling technique. 22nd International Congress of Aeronautical Science (ICAS) Conference

      [25] Aksit I & Moss J (2005), Model fuels to reproduce the sooting behaviour of aviation kerosene. Fuel 84(2), 239-245

      [26] Kao YH, Tambe SB, Ochs R, Summer S & Jeng SM (2017), Experimental study of the burner for FAA fire test: NexGen burner. Fire and Materials 41, 898-907

      [27] Mohammed I, Abu Talib AR, Sultan MTH & Saadon S (2016), Temperature and heat flux measurement techniques for aeroengine fire test: a review. IOP Conference Series: Materials Science and Engineering 152, 012036

      [28] Balland M, Verseux O & Esteve M-J (2005), Aero thermal computations with experimental comparison applied to aircraft engine nacelle compartment. ASME Turbo Expo, Power for Land, Sea, and Air

      [29] Mrazova M (2013), Advanced composite materials of the future in aerospace industry. Incas bulletin 5(3), 139

      [30] Sikoutris DE, Vlachos DE, Kostopoulos V, Jagger S & Ledin S (2012), Fire burnthrough response of CFRP aerostructures. Numerical investigation and experimental verification. Applied Composite Materials 19(2), 141-159

      [31] Williams JC & Starke EA (2003), Progress in structural materials for aerospace systems. Acta Materialia 51(19), 5775-5799

      [32] Zikre H & Bhatt A (2015), Comparison of mechanical properties of fiber reinforced plastic laminates compose with different thicknesses, manufacturing techniques and structures. International Conference on Multidisciplinary Research & Practice

      [33] Rajkumar G, Krishna M, Narasimhamurthy H, Keshavamurthy Y & Nataraj J (2014), Investigation of tensile and bending behavior of aluminum based hybrid fiber metal laminates. Procedia Materials Science 5, 60-68

      [34] Anon. (1998), ISO2685: Aircraft environmental test procedures for airborne equipment – Resistance to fire in designated fire zones. International Organization of Standardization

      [35] Anon. (2014), D3039/D3039M-14: Standard Test Method for Tensile Properties of polymer matrix composite materials. ASTM International

      [36] Anon. (2016), D3410/D3410-16: Standard Test for Compressive of Polymer Matrix Composite Material with Unsupported Gage Section by Shear Loading, ASTM International

      [37] Anon. (2007), ASTM I: Standard test methods for flexural properties of unreinforced and reinforced plastics and electrical insulating materials. ASTM D790-07

      [38] Hooijmeijer P & Vlot A (1998), Fibre metal laminates exposed to high temperatures. Delft University of Technology

      [39] Quintiere JG (2006), Fundamentals of fire phenomena. Wiley Online Library

      [40] Tewarson A (1994), Flammability parameters of materials: ignition, combustion and fire propagation. Journal of Fire & Flammability 12(4), 329-356

      [41] Bartlett J & Stratford C (2001), Fire resistance certification of aircraft composite materials. Practical Failure Analysis 1(6), 37-43

      [42] Botelho E, Almeida R, Pardini L & Rezende M (2007), Influence of hygrothermal conditioning on the elastic properties of Carall laminates. Applied Composite Materials 14(3), 209-222

      [43] Mendez J, Vilaseca F, Pelach M, Lopez J, Barbera L, Turon X, Girones J & Mutje P (2007), Evaluation of the reinforcing effect of ground wood pulp in the preparation of polypropyleneâ€based composites coupled with maleic anhydride grafted polypropylene. Journal of Applied Polymer Science 105(6), 3588-3596

      [44] Mutjé P, Vallejos M, Girones J, Vilaseca F, López A, López J & Méndez J (2006), Effect of maleated polypropylene as coupling agent for polypropylene composites reinforced with hemp strands. Journal of Applied Polymer Science 102(1), 833-840

      [45] Vilaseca F, Valadez-Gonzalez A, Herrera-Franco PJ, Pèlach MÀ, López JP & Mutjé P (2010), Biocomposites from abaca strands and polypropylene. Part I: Evaluation of the tensile properties. Bioresource Technology 101(1), 387-395

      [46] Zhang D, Sun Y, Chen L, Zhang S & Pan N (2014), Influence of fabric structure and thickness on the ballistic impact behavior of Ultrahigh molecular weight polyethylene composite laminate. Materials & Design 54, 315-322

      [47] Sabet AR, Beheshty MH & Rahimi H (2009), Experimental study of sharpâ€tipped projectile perforation of GFRP plates containing sand filler under high velocity impact and quasiâ€static loadings. Polymer Composite 30(10), 1497-1509

      [48] Razali N, Sapuan S, Jawaid M, Ishak MR & Lazim Y (2016), Mechanical and thermal properties of Roselle fibre reinforced vinyl ester composites. BioResources 11(4), 9325-9339

  • Downloads

  • How to Cite

    Mohammed, I., Rahim Abu Talib, A., Thariq Hameed Sultan3, M., & Sadoon, S. (2018). Fire behavioural and mechanical properties of carbon fibre reinforced aluminium laminate composites for aero-engine. International Journal of Engineering & Technology, 7(4.13), 22-27. https://doi.org/10.14419/ijet.v7i4.13.21323

    Received date: 2018-10-08

    Accepted date: 2018-10-08

    Published date: 2018-10-09