Characterization of Biocomposite Film Coating for Food Paper Packaging

  • Authors

    • Nurul Fatin Alia Mustapha
    • Zatul Iranati Md. Sharif
    • Junaidah Jai
    • Noorsuhana Mohd Yusof
    • Sitinoor Adeib Idris
    2018-11-27
    https://doi.org/10.14419/ijet.v7i4.18.21944
  • Biocomposite film, Cassava starch, Carboxymethylcellulose, Food packaging, Paper coating

  • Abstract

    Paper and paperboard are commonly laminated with petroleum-based plastic such as polyethylene (PE) to enhance its barrier and mechanical properties. However, it cannot be degraded naturally by the environment. In an effort to counter this issue, natural sources biopolymer film was developed from cassava starch and carboxymethylcellulose (CMC) as alternatives in replacing PE. Different formulation viscosity was prepared by varying the contents of CMC in cassava starch from 0% to 50%. Characterizations analysis showed that sample BF 3 containing 10% w/w starch of CMC had the highest tensile strength (15 MPa), exhibited hydrophobic properties with contact angle higher than 90° and had the lowest moisture content. Fourier Transform Infrared (FTIR) analysis on BF 3 confirmed the presence of C-OH bending at C-6 of glycosidic ring indicated the presence of intermolecular and intramolecular hydrogen bond formation. A comparison study of BF 3 with commercially coating material  used in food packaging showed that BF 3 exhibit similar hydrophobic properties but higher tensile strength than the PE coating. Besides, thermogravimetric analysis identified that BF 3 had less residue and this indicated that BF 3 film degraded faster than the commercial. Thus, it can be stated that the develop biofilm could replace the currently used petroleum based derivative plastic in the food industry. 

     

     

  • References

    1. [1] Coles, R., McDowell, D., & Kirwan, M. J. (2003). Packaging Technology Series: Food Packaging Technology. London, U.K.: Blackwell Publishing.

      [2] Marsh, K., & Bugusu, B. (2007). Food Packaging-Roles, Materials, and Environmental Issues. Packaging, Food, and Environmental Issues, 72(3), 39–56.

      [3] Sung, S., Sin, L., Bee, S., et al. (2013). Antimicrobial agents for food packaging applications. Trends in Food Science and Technology, 1–14.

      [4] Kanmani, P., & Rhim, J. (2014). Development and characterization of carrageenan / grapefruit seed extract composite films for active packaging. International Journal of Biological Macromolecules, 68, 258–266.

      [5] M. Chaplin, “Sources for starch,†Water Structure and Science, 2018. [Online]. Available: http://www1.lsbu.ac.uk/water/starch.html.

      [6] Skurtys, O., Acevedo, C., Pedreschi, F., Enrione, J., Osorio, F., & Aguilera, J. . (2010). Food hydrocolloid edible films and coatings. Science & Engineering. 318-380.

      [7] Nieto, M. B. (2009). Edible films and coatings for food applications: Structure and function of polysaccharide gum-based edible films and coatings. Springer. New York.

      [8] Lian, T. S., & Idris, K. (2000). Present situation and future potential of cassava in Malaysia. Kuala Lumpur, Malaysia.

      [9] Parra, D., Tadini, C., Ponce, P., & Lugao, A. (2004). Mechanical properties and water vapor transmission in some blends of cassava starch edible films. Carbohydrate Polymers, 58(4), 475–481.

      [10] Maran, J. P. P., Sivakumar, V., Sridhar, R., & Thirugnanasambandham, K. (2013). Development of model for barrier and optical properties of tapioca starch based edible films. Carbohydrate Polymers, 92(2), 1335–1347.

      [11] Ghanbarzadeh, B., Almasi, H., & Entezami, A. A. (2010). Physical properties of edible modified starch/carboxymethyl cellulose films. Innovative Food Science and Emerging Technologies, 11(4), 697–702.

      [12] Fennema, O. R., Kamper, S. L., & Kester, J. J. (1990). U.S. Patent No. 4,915-971. Wisconsin Alumni Research Foundation, Madison, Wis.

      [13] Rastogi, V. K., & Samyn, P. (2015). Bio-based coatings for paper applications. Coatings, 5, 887–930.

      [14] Mali, S., Sakanaka, L. S., Yamashita, F., & Grossmann, M. V. E. (2005). Water sorption and mechanical properties of cassava starch films and their relation to plasticizing effect. Carbohydrate Polymers, 60(3), 283–289.

      [15] Alves, V., Costa, N., Hilliou, L., Larotonda, F., Goncalves, M., & Sereno, A. (2006). Design of biodegradable composite films for food packaging. Desalination, 1, 331–333.

      [16] Hong, K. M. (2013). Preparation and characterization of carboxymethylcellulose from sugarcane bagasse (Degree Thesis). Universiti Tunku Abdul Rahman, Kuala Lumpur, Malaysia.

      [17] Suderman, N., Isa, M. I. N., & Sarbon, N. M. (2016). Effect of drying temperature on the functional properties of biodegradable CMC-based film for potential food packaging. International Food Research Journal, 23(3), 1075–1084.

      [18] Tabari, M. (2017). Effect of carboxymethyl cellulose on the mechanical and barrier properties of sago starch based films,†Preprints, 1, 1–7.

      [19] Aqualon. (1999). Physical and chemical properties of sodium carboxymethylcellulose. Hercules Incorporated, 6.

      [20] Liu, Y., Cai, Y., Jiang, X., Wu, J., & Le, X. (2016). Molecular interactions , characterization and antimicrobial activity of curcumin-chitosan blend films. Food Hydrocolloids, 52, 564–572.

      [21] Shogren, R. L. (1999). Preparation and characterization of a biodegradable mulch : paper coated with polymerized vegetable oils. Journal of Applied Polymer Science, 73, 2159–2167.

      [22] Turhan, K. N., Şahbaz, F., & Güner, A. (2001). A spectrophotometric study of hydrogen bonding in methylcellulose-based edible films plasticized by polyethylene glycol. Journal of Food Science, 66(1), 59–62.

      [23] Cisneros-Zevallos, L., & Krochta, J. M. (2003). Dependence of coating thickness on viscosity of coating solution applied to fruits and vegetables by dipping method. Journal of Food Science, 68(2), 503–510.

      [24] Battersby, G. C., Santos, S. A., Zhong, B., & Gan, X. (2015). U.S. Patent No. 9102125 B2. Mantrose-Haeuser Co., Inc.

      [25] Paunonen, S. (2010). Influence of moisture on the performance of polyethylene coated solid fiberboard and boxes (PhD Thesis). Norwegian University of Science and Technology, Trondheim, Norway.

      [26] Tashiro, K., & Kobayashi, M. (1991). Theoretical evaluation of three-dimensional elastic constants of native and regenerated cellulose: Role of hydrogen bonds. Polymer, 32(8), 1516–1526.

      [27] Fan, M., Dai, D., & Huang, B. (2012). Fourier Transform Infrared Spectroscopy for natural fibres. Fourier Transform Materials Analysis, 45–68.

      [28] Balan, T., Guezennec, C., Nicu, R., Ciolacu, F., & Bobu, E. (2015). Improving barrier and strength properties of paper by multi-layer coating with bio-based additives. Cellulose Chemistry and Technology, 49, 607–615.

      [29] Basiak, E., Debeaufort, F., & Lenart, A. (2016). Effect of oil lamination between plasticized starch layers on film properties. Food Chemistry, 195, 56–63.

      [30] Sichina, W. J. (2010). Characterization of polymers using TGA. Thermal Analysis Perkin Elmer Instruement, 1–5.

      [31] Beyler, C. L., & Hirschler, M. M. (2010). Thermal decomposition of polymers. SFPE Handbook of Fire Protection Engineering, 110–131.

  • Downloads

  • How to Cite

    Fatin Alia Mustapha, N., Iranati Md. Sharif, Z., Jai, J., Mohd Yusof, N., & Adeib Idris, S. (2018). Characterization of Biocomposite Film Coating for Food Paper Packaging. International Journal of Engineering & Technology, 7(4.18), 325-330. https://doi.org/10.14419/ijet.v7i4.18.21944

    Received date: 2018-11-27

    Accepted date: 2018-11-27

    Published date: 2018-11-27