The Characteristic of Cobalt-Nickel-Iron Alloy Coating Coated on Aluminium, Brass and Stainless Steel

  • Authors

    • Nik Rozlin N.M Masdek
    • Zuraidah Salleh
    • Md Zin Abu
    • . .
    2018-11-30
    https://doi.org/10.14419/ijet.v7i4.26.22146
  • Co-Ni-Fe, electrodeposition, nanoparticles, microhardness

  • Electrodeposition is a well-known and economical method in the coating industry due to its low cost and fast process. This study investigates on the charateristic of electrodeposited Co-Ni-Fe alloy coating coated on three different substrates that is aluminium, brass and stainless steel. The surface morphology, microhardness, surface roughness, and corrosion resistance of Co-Ni-Fe electrodeposited on aluminium, brass and stainless steel was determined. This study compares the different properties of the Co-Ni-Fe alloy coating coated on aluminium, brass and stainless steel which can enhance the mechanical, chemical and corrosion properties of these metals. Aluminium deposited with Co-Ni-Fe alloy coating had the highest microhardness of 427.4 Hv as compared to brass and stainless steel. Meanwhile the surface roughness for all metals deposited with Co-Ni-Fe alloy coating was reduced significantly. In terms of the corrosion behavior, brass coated with Co-Ni-Fe alloy coating has the lowest corrosion rate of 4.699x10-3 mmpy while stainless steel and aluminium had a corrosion rate of 19.82x10-3 mmpy and 66.15x10-3 mmpy, respectively. From the findings it can be seen that microhardness and corrosion resistance showed an increase of about 40% after depositing the aluminium, brass and stainless steel with Co-Ni-Fe alloy coating.

     

     

  • References

    1. [1] E. H. Hollingworth and H. Y. Hunsicker, Corrosion of aluminium and aluminium alloys, vol. 2. 1990.

      [2] N. H. B. Minhat, “Investigation of Brass Microstructure and Mechanical Properties using Metal Casting.pdf.†2010.

      [3] Journal, M. Engineering, and P. Doi, “Experimental Analysis of Microstructure and Mechanical,†vol. 11, no. June, pp. 2317–2331, 2015.

      [4] P. N. Barlett and J. M. Cooper, A review of the immobilization of enzymes in electropolymerized films, vol. 362. 1993.

      [5] Gurrappa and L. Binder, “Electrodeposition of nanostructured coatings and their characterization - A review,†Sci. Technol. Adv. Mater., vol. 9, no. 4, 2008.

      [6] N. Rozlin, N. Masdek, N. Fazli, A. Manan, Z. Salleh, and K. Mei, “Characterization of Electrodeposited Nanocrystalline Cobalt- Iron Coating with Different Iron Content,†vol. 120009, 2017.

      [7] K. Kumar, H. van swygenhoven, and S. Suresh, Mechanical Behavior of Nanocrystalline Metals and Alloys, vol. 51. 2003.

      [8] F. Renner, A. Stierle, H. Dosch, D. M Kolb, T.-L. Lee, and J. Zegenhagen, Initial corrosion observed on the atomic scale, vol. 439. 2006.

      [9] G. Herzer, Grain size dependence of coercivity and permeability in nanocrystalline ferromagnets, vol. 26. 1990.

      [10] N. A. Resali, K. M. Hyie, M. N. Berhan, Z. Salleh, and S. Kasolang, “Cobalt-nickel-iron nanoparticles coated on stainless steel substrate,†Procedia Eng., vol. 68, no. May, pp. 30–36, 2013.

      [11] N. G. Kong, B. Gong, and G. Wang, “Influence Of Surface Roughness Of Substrate On The Properties Of Ni – Co – Fe Electrodeposition Coating On Copper,†vol. 1850120, pp. 1–8, 2017.

      [12] N. A. Resali, K. M. Hyie, M. N. Berhan, N. R. Nik Roselina, and C. M. Mardziah, “Corrosion behavior of electrodeposited CoNiFe nanoparticles immersed in different environments,†Appl. Mech. Mater., vol. 607, pp. 33–36, 2014.

      [13] M. Tafreshi, S. R, and H. Farhangi, “Comparative study on structure, corrosion properties and tribological behavior of pure Zn and different ZnNi alloy coatings,†Mater. Chem. Phys., 2016.

      [14] T. Element, “10.1 The Element,†pp. 225–245, 2010.

      [15] E. Marin and A. Lanzutti, “Tribological Properties of Nanometric Atomic Layer Depositions Applied on AISI 420 Stainless Tribological Properties of Nanometric Atomic Layer Depositions Applied on AISI 420 Stainless Steel Tribology in Industry,†no. September, 2013.

      [16] N. M. N. Rozlin, A. M. Alfantazi, “Electrochemical properties of electrodeposited nanocrystalline cobalt and cobalt – iron alloys in acidic and alkaline solutions,†pp. 721–734, 2013.

      [17] J. George, J. Rantschler, S. Bae, D. Litvinov, and S. R. Brankovic, “Sulfur and Saccharin Incorporation into Electrodeposited CoFe Alloys : Consequences for Magnetic and Corrosion Properties,†pp. 0–5, 2008.

      [18] K. M. Hyie, A. Ahmad, N. A. Resali, M. F. Munir, C. S. Li, and S. Saidin, “Corrosion Study of Electrodeposited Co-Ni-Fe Protective Coating on Electroless Nickel Immersion Gold (ENIG) Flexible Printed Circuit,†Procedia Technol., vol. 15, no. December, pp. 792–797, 2014.

  • Downloads

  • How to Cite

    Rozlin N.M Masdek, N., Salleh, Z., Zin Abu, M., & ., . (2018). The Characteristic of Cobalt-Nickel-Iron Alloy Coating Coated on Aluminium, Brass and Stainless Steel. International Journal of Engineering & Technology, 7(4.26), 97-101. https://doi.org/10.14419/ijet.v7i4.26.22146