Chromium Carbonitride (CrCN) Coatings on SUS 316L with Potential Application as Bipolar Plate in PEMFC

  • Authors

    • Nur Fawwaz Asri
    • Teuku Husaini
    • Abu Bakar Sulong
    • Edy Herianto Majlan
    • Wan Ramli Wan Daud
    • Bushroa Abdul Razak
    • Nabilah Afiqah Mohd Radzuan
    2019-01-24
    https://doi.org/10.14419/ijet.v8i1.1.24779
  • CrCN, SUS 316L, bipolar plate, corrosion behavior, interfacial contact resistance.

  • Abstract

    The effects of corrosion behavior and interfacial contact resistance (ICR) of sputtered chromium carbonitride (CrCN) on SUS 316L are investigated. The corrosion behavior of CrCN coatings as potential bipolar plates in proton exchange membrane fuel cells (PEMFCs) are studied by potentiodynamic tests in 0.5 M sulfuric acid (H2SO4) with a scan rate of 1 mV/S. The ICR values are measured to evaluate electrical conductivity. The surface topography and roughness are monitored by atomic force microscopy (AFM) to investigate the surface features of CrCN coatings that correspond to the X-ray powder diffraction (XRD) analysis. The diffraction peak of CrCN has a current density (Icorr) of 0.1 µA cm‒2 and ICR of 2.12 mΩ cm² at 80 ºC after the coated 316L is polarized. The formed metal nitrides and carbides possess prominent physical and chemical properties, such as superconductivity, high hardness, high melting points, high electrical conductivity and good corrosion resistance. Favorable factors are observed in CrCN of Sample C with 150 W and 80 min deposition that resists corrosion either at the anode or cathode side in the PEMFC. Coating materials using CrCN are proposed to improved bipolar plates, to achieve the single cell performance in PEMFCs.

     

     

  • References

    1. [1] N.F. Asri, T. Husaini, A.B. Sulong, E.H. Majlan, W.R.W. Daud (2017), Coating of stainless steel and titanium bipolar plates for anticorrosion in PEMFC: A review, International Journal of Hydrogen Energy, 42, 9135-9148.

      [2] R. Taherian (2014), A review of composite and metallic bipolar plates in proton exchange membrane fuel cell: Materials, fabrication, and material selection, Journal of Power Sources, 265, 370-390.

      [3] J.-J. Hwang (2013), Sustainability study of hydrogen pathways for fuel cell vehicle applications, Renewable and Sustainable Energy Reviews, 19, 220-229.

      [4] A.F. Ambrose, A.Q. Al-Amin, R. Rasiah, R. Saidur, N. Amin (2017), Prospects for introducing hydrogen fuel cell vehicles in Malaysia, International Journal of Hydrogen Energy, 42, 9125-9134.

      [5] R.A. Huggins (2016), Hydrogen Storage, Energy Storage, Springer, pp. 95-118.

      [6] T. Fukutsuka, T. Yamaguchi, S.-I. Miyano, Y. Matsuo, Y. Sugie, Z. Ogumi (2007), Carbon-coated stainless steel as PEFC bipolar plate material, Journal of Power Sources, 174, 199-205.

      [7] W. Mingge, L. Congda, H. Tao, C. Guohai, W. Donghui (2016), Chromium interlayer amorphous carbon film for 304 stainless steel bipolar plate of proton exchange membrane fuel cell, Surface and Coatings Technology, 307, 374-381.

      [8] C. Liu, Q. Bi, A. Leyland, A. Matthews (2003), An electrochemical impedance spectroscopy study of the corrosion behaviour of PVD coated steels in 0.5 N NaCl aqueous solution: Part II.: EIS interpretation of corrosion behaviour, Corrosion Science, 45, 1257-1273.

      [9] P. Yi, L. Peng, T. Zhou, H. Wu, X. Lai (2013), Cr–N–C multilayer film on 316L stainless steel as bipolar plates for proton exchange membrane fuel cells using closed field unbalanced magnetron sputter ion plating, international journal of hydrogen energy, 38, 1535-1543.

      [10] Y. Zhao, L. Wei, P. Yi, L. Peng (2016), Influence of Cr-C film composition on electrical and corrosion properties of 316L stainless steel as bipolar plates for PEMFCs, International Journal of Hydrogen Energy, 41, 1142-1150.

      [11] X.Z. Yuan, H. Wang, J. Zhang, D.P. Wilkinson (2005), Bipolar plates for PEM fuel cells-from materials to processing, Journal of New Materials for Electrochemical Systems, 8, 257.

      [12] F. Alresheedi, J. Krzanowski (2017), Structure and morphology of stainless steel coatings sputter-deposited in a nitrogen/argon atmosphere, Surface and Coatings Technology, 314, 105-112.

      [13] A. Bushroa, H. Masjuki, M. Muhamad (2011), Parameter optimization of sputtered Ti interlayer using Taguchi method, International Journal of Mechanical and Materials Engineering, 6, 140-146.

      [14] [14] H. Husby (2013), Carbon Based Coatings for Metallic Bipolar Plates in PEM Fuel Cells, NTNU, Norwegian University of Science and Technology, pp. 1-106.

      [15] S. Lee, N. Kakati, J. Maiti, S. Jee, D. Kalita, Y. Yoon (2013), Corrosion and electrical properties of CrN-and TiN-coated 316L stainless steel used as bipolar plates for polymer electrolyte membrane fuel cells, Thin Solid Films, 529, 374-379.

      [16] Y. Hung, H. Tawfik, K. El-Khatib, H. El-Abd (2008), Corrosion and contact resistance measurements of different bipolar plate material for Polymer Electrolyte Membrane Fuel Cells, International Journal of Alternative Propulsion, 2, 72-85.

      [17] S. Lædre (2011), Investigation of metallic bipolar plates for PEM fuel cells, Institutt for materialteknologi.

      [18] H. Pengfei, J. Bailing (2011), Study on tribological property of CrCN coating based on magnetron sputtering plating technique, Vacuum, 85, 994-998.

      [19] M. Kazmanli, M. Ürgen, A. Cakir (2003), Effect of nitrogen pressure, bias voltage and substrate temperature on the phase structure of Mo–N coatings produced by cathodic arc PVD, Surface and Coatings Technology, 167, 77-82.

      [20] C.-H. Hsu, W.-C. Huang, Y.-P. Lee, W.-Y. Ho (2017), Effect of nitrogen atmosphere heat treatment on structure and wear behavior of CrAlSiN nanocomposite film, Surface and Coatings Technology, 320, 230-234.

      [21] K. Lin, X. Li, Y. Sun, X. Luo, H. Dong (2014), Active screen plasma nitriding of 316 stainless steel for the application of bipolar plates in proton exchange membrane fuel cells, International Journal of Hydrogen Energy, 39, 21470-21479.

      [22] Y. Kong, X. Tian, C. Gong, P.K. Chu (2018), Enhancement of toughness and wear resistance by CrN/CrCN multilayered coatings for wood processing, Surface and Coatings Technology, 344, 204-213.

      [23] H.-P. Feng, C.-H. Hsu, J.-K. Lu, Y.-H. Shy (2003), Effects of PVD sputtered coatings on the corrosion resistance of AISI 304 stainless steel, Materials Science and Engineering: A, 347, 123-129.

      [24] W. Griffiths, A. Gerrard, Y. Yue (2016), Oxide film defects in Al alloys and the formation of hydrogen-related porosity, IOP Conference Series: Materials Science and Engineering, IOP Publishing, pp. 1-6.

      [25] M. Fenker, M. Balzer, H. Kappl (2014), Corrosion protection with hard coatings on steel: Past approaches and current research efforts, Surface and Coatings Technology, 257, 182-205.

      [26] E. Cho, U.-S. Jeon, S.-A. Hong, I.-H. Oh, S.-G. Kang (2005), Performance of a 1kW-class PEMFC stack using TiN-coated 316 stainless steel bipolar plates, Journal of power sources, 142, 177-183.

      [27] S. Shimpalee, V. Lilavivat, H. McCrabb, Y. Khunatorn, H.-K. Lee, W.-K. Lee, J. Weidner (2016), Investigation of bipolar plate materials for proton exchange membrane fuel cells, International Journal of Hydrogen Energy, 41(31), pp. 13688-13696.

  • Downloads

  • How to Cite

    Fawwaz Asri, N., Husaini, T., Bakar Sulong, A., Herianto Majlan, E., Ramli Wan Daud, W., Abdul Razak, B., & Afiqah Mohd Radzuan, N. (2019). Chromium Carbonitride (CrCN) Coatings on SUS 316L with Potential Application as Bipolar Plate in PEMFC. International Journal of Engineering & Technology, 8(1.1), 44-52. https://doi.org/10.14419/ijet.v8i1.1.24779

    Received date: 2018-12-25

    Accepted date: 2018-12-25

    Published date: 2019-01-24