Influence of Friction Pressure at a Given Burn-off Length on the Mechanical and Microstructural Properties of Welded Joints from Medium-Carbon Alloyed Steels in Rotaty Friction Welding

  • Authors

    • Elena Priymak
    • Nadezhda Firsova
    • Elena Bashirova
    • Svetlana Sergienko
    • Elena Kuzmina
    • Artem Atamashkin
    2018-12-09
    https://doi.org/10.14419/ijet.v7i4.36.24934
  • rotaty friction welding, welded joints, thermomechanical affected zone, microstructure, microhardness, tensile strength

  • Abstract

    This study investigates the influence of friction pressure at a given  burn-off length on the microhardness, tensile properties and microstructure of the welded joints from steel 32-2-Mn and 40-Cr-Ni. Phase transformations occurring in the materials to be welded as a result of thermal deformation effects are analyzed. The change in the length of the thermomechanical affected zone (TMAZ) depending on the friction pressure is shown. The results of the distribution of microhardness in the weld, clearly illustrating the formation of hardened and weakened areas. The results of tensile tests of welded joints are given. Analyzed the place of fracture at various welding parameters. The necessity of studying the distribution of internal residual stresses to explain the mechanism of fracture of welded joints is shown.

     

     

  • References

    1. [1] Sahin M. Joining with friction welding of high- speed steel and medium-carbon steel, Journal of Materials Processing Technology, Vol. 168, pp. 202– 210. 2005. DOI: 10.1016/j.jmatprotec.2004.11.015

      [2] Sahin M. Characterization of properties in plastically deformed austenitic-stainless steels joined by friction Welding, Materials and Design, Vol 30, pp. 135–144. 2009. DOI: 10.1016/j.matdes.2008.04.033

      [3] Sahin M. Evaluation of the joint-interface properties of austenitic-stainless steels (AISI 304) joined by friction welding, Materials and Design, Vol. 28, pp. 2244–2250. 2007 DOI: 10.1016/j.matdes.2006.05.031

      [4] Ozdemira N. Sarsılmaz F., Hascalık A. Effect of rotational speed on the interface properties of friction- welded AISI 304L to 4340 steel, Materials and Design, Vol. 28, pp. 301–307. 2005. DOI: 10.1016/j.matdes.2005.06.011

      [5] Selvamani1 S.T., Umanath K., Palanikumar K., Vigneswar K. (2014). The microhardness analysis of friction welded AISI 52100 grade carbon steel joints, Advanced Materials Research, Vol. 984-985, pp. 613- 617. DOI: 10.4028/www.scientific.net/AMR.984-985.613

      [6] Tomoyuki U., Shigeharu U., Tatsuyoshi N., Masayuki Fujiwara. (2007). Properties of friction welds between 9Cr-ODS martensitic and ferritic–martensitic steels, Journal of Nuclear Materials, Vol. 367, pp. 1213– 1217. DOI: 10.1016/j.jnucmat.2007.03.221

      [7] Satyanarayana V.V., Madhusudhan R.G., Mohandas T. (2005). Dissimilar metal friction welding of austenitic–ferritic stainless steels, Journal of Materials Processing Technology, Vol. 160, pp. 128–137. DOI: 10.1016/j.jmatprotec.2004.05.017

      [8] Kalsi. N.S., Sharma V. S. A statistical analysis of rotary friction welding of steel with varying carbon in workpieces, Int J Adv Manuf Technol, 2011, DOI: 10.1007/s00170-011-3361-z.

      [9] Demouche M., Ouakdi el Hedj , Louahdi R. , Maati A. Experimental characterization of the Heat Affected Zone (HAZ) properties of 100Cr6 steel joined by rotary friction welding method

      [10] Ates H, Kaya N, Mechanical and microstructural properties of friction welded AISI 304 stainless steel to AISI 1060 steel, Archives of metallurgy and materials, Vol. 59, pp. 841-846. DOI: 10.2478/amm-2014-0142

      [11] P.Sathiya, S. Aravidan, A. Noorul Haq, Effect of friction welding parameters on mechanical and metallurgical properties of ferritic stainless steel, Int. J. Adv. Manufac.Technol. 31, 1076-1082 (2007).

      [12] S.D. Meshram, T. Mohandas, G.M. Reddy, Friction welding of dissimilar pure metals, J. Mater. Proces. Techn. 184, 330-337 (2007)

      [13] A. Kurt, I. Uygur, U. Paylasan, Effect of friction welding parameters on mechanical and microstructural properties of dissimilar AISI 1010-ASTMB22 joints, Welding Journal 90, 102-106 (2011).

      [14] H. Ates, M. Turker, A. Kurt, Effect of friction pressure on the properties of friction welded MA956 iron-based superalloy, Mater. & Design 28, 948-953 (2007).

      [15] S.Y. Kim, S.B. Jung, C.C. Shur, Mechanical properties of copper to titanium joined by friction welding, J. Mater. Scien. 38, 1281-1287 (2003).

      [16] M. Sahin, H.E. Akata, K. Ozel, An experimental study on joining of severe plastic deformed aluminum materials with friction welding method, Mater. & Design 29(1), 265-274 (2008).

      [17] Emre, H.E., Kaçar, R. Fatigue behaviours of friction welded drill pipes // Journal of the Faculty of Engineering and Architecture of Gazi University. 2013

      [18] M. Kimura, M. Kusaka, K. Seo, Y. Otsuka & A. Fuji, Effects of Friction Time and Friction Pressure on Tensile Strength of Medium- and High-Carbon Steel Welded Joints by Low-Heat Input Friction Welding Methodâ€, Welding International, Vol, 20, No. 10, pp. 767-776, 2006.

  • Downloads

  • How to Cite

    Priymak, E., Firsova, N., Bashirova, E., Sergienko, S., Kuzmina, E., & Atamashkin, A. (2018). Influence of Friction Pressure at a Given Burn-off Length on the Mechanical and Microstructural Properties of Welded Joints from Medium-Carbon Alloyed Steels in Rotaty Friction Welding. International Journal of Engineering & Technology, 7(4.36), 978-982. https://doi.org/10.14419/ijet.v7i4.36.24934

    Received date: 2018-12-28

    Accepted date: 2018-12-28

    Published date: 2018-12-09