Thermal Performance on Tapering Heat Pipe

 
 
 
  • Abstract
  • Keywords
  • References
  • PDF
  • Abstract


    Various design of heat pipes had been developed in previous research to enhance thermal performance. In this study, tapering heat pipe is developed. The method used true experimental to observe temperature distribution in the heat pipe. Geometric design is set as the ratio of diameter evaporator (d) and condenser (D) which are d/D =1/1, 1/2, 1/3 and 1/4. Heat source (Q) is varied by using DC power supply of 25, 30, 35, 40, 45 and 50 Watt. The temperature was measured by using k-type thermocouple with NI-9211 and c-DAQ 9271 module. Wick heat pipe is set as screen mesh with 56,5 µm wire diameter with one single layer. Wick screen mesh material used is stainless steel with 40 W/(m•K) thermal conductivity on layer shape. Thermal resistance decrease, high evaporation time, and stable temperature distribution are an indicator performance to determine the best thermal performance. Based on the results, it can be denoted that d/D and Q affected to thermal performance difference. Both of d/D and Q increased, thermal performance increases. The tapering heat pipe with d/D = 1/4 and Q = 50 Watt provide the better thermal performance.

     


  • Keywords


    Tapering Heat Pipe, Thermal Performance, Ratio Diameter Evaporator and Condenser, Heat Source

  • References


      [1] A. Faghri, Heat pipe science and technology, Taylor & Francis publishing, Oxon (1995).

      [2] A. Brautsch, P.A. Kew., Examination and visualization of heat transfer processes during evaporation in capillary porous structures, Appl. Therm. Eng. 22 (2002) 815–824

      [3] C.Li, G.P.Peterson, Y.Wang, Evaporation/ boiling in thin capillary wicks (I) – wick thickness effects, J. Heat Transfer 128 (2006) 1312–1319

      [4] H.T. Chien, C.T. Tsai, P.H. Chen, P.Y. Chen, Improvement on thermal performance of a disk-shaped miniature heat pipe with Nanofluids, in: Proceedings of the Fifth International Conference on Electronic Packaging Technology, IEEE, Shanghai, China, 2003, pp. 389e391

      [5] Harris, James R., Modeling, Designing, Fabricating and Testing of Channel Panel Flat Plate Heat Pipe. Utah State University, pp.1-6, 2008

      [6] Liang TS, Hung YM., Experimental investigation on the thermal performance and optimization of heat sink with U-shape heat pipes. Energy Convers Manage 2010; 51:21: 09-16

      [7] Reay, David & Peter Kew., Heat Pipe, Theory, Design and Applications, 5th Edition, USA, 2006

      [8] Russel MK, Young C, Cotton JS, Ching CY, The effect of orientation on U-shaped grooved and sintered wick heat pipe, Appl Therm Eng 2011; 31: 69-76

      [9] R. Senthilkumar, S. Vaidyanathan, B. Sivaraman, Effect of Inclination Angle in Heat Pipe Performance Using Copper Nanofluid, Procedia Engineering 38 (2012); 3715 – 3721

      [10] S.M. Peyghambarzadeh, S. Shahpouri, N. Aslanzadeh, M. Rahimnejad, Thermal performance of different working fluids in a dual diameter circular heat pipe, Ain Shams Engineering Journal (201


 

View

Download

Article ID: 26683
 
DOI: 10.14419/ijet.v8i1.9.26683




Copyright © 2012-2015 Science Publishing Corporation Inc. All rights reserved.