Applying Using Structural-Parametric Geometric Models for Rational Design of Technological Processes in Mechanical Engineering

  • Authors

    • Gennadii Virchenko
    • Viacheslav Martynov
    • Oleg Sergeychuk
    • Valery Usenko
    2018-10-13
    https://doi.org/10.14419/ijet.v7i4.8.27308
  • designing technological processes, engineering, optimization, structural-parametric geometric models.

  • Abstract

    The article is devoted to some questions of applying the methodology of structural-parametric geometric modeling in modern machine building. Theoretical and practical relevance of the mentioned scientific-applied theme has been substantiated. The main purpose of this publication is to describe the basic provisions of the proposed method of rational computer design of groups of technical objects and the design of technological processes of their production. The corresponding examples of practical use of the considered modeling techniques concerning mechanical parts manufactured by cutting are presented and analyzed. The main advantages of these techniques have been substantiated in comparison with the existing traditional methods of designing technological processes in mechanical engineering. The basic prospective directions of carrying out further scientific researches concerning the outlined subjects have been determined.

     

     

  • References

    1. [1] B. Ketul, M. Dipal, K. Nirmit, â€Parametric modeling of Oldham couplingâ€, International Journal of Innovative Research in Science, Engineering and Technology, Vol.3, No.2, (2014), pp.9120-9125.

      [2] D. Popescu, L. Chioltean, â€Design Configuration under Parametric Controlâ€, Scientific Bulletin of the Politehnica University of Timisoara, Transactions on Hydrotechnics, Vol.58, No.72, (2013), pp. 67-70.

      [3] W. Sun, H. Ma, C. Li, B. Wen, â€Study on Parametric Modeling Based on Visual Optimization Design of Mechanical Productâ€, Proceedings of the Second International Conference on Intelligent Computation Technology and Automation, (2009), DOI: 10.1109/icicta.2009.304

      [4] V. Pomazan, “Assembly Top Down Design in Parametric CADâ€, Scientific Bulletin of the Politehnica University of Timisoara, Transactions on Hydrotechnics, Vol.58, No.72, (2013), pp.153-156.

      [5] V. Vanin, G. Virchenko, â€Definition and basic positions of structural-parametric geometric modeling†(in Ukrainian), Geometric and computer modeling, Vol.23, (2009), pp.42-48.

      [6] V. Vanin, G. Virchenko, V. Vanin, â€Structural-parametric geometric models as an invariant component of computer information technologies supporting the life cycle of machine-building products†(in Ukrainian), Proceedings of the Tavria State Agrotechnological Academy, Vol.4, No.36, (2007), pp.16-21.

      [7] V. Vanin, G. Virchenko, I. Vanin, â€Structural-parametric geometrical models as a basis for the coordinated elaboration of the airplane at the stage of sketch design†(in Ukrainian), Scientific news of the NTUU "Kyiv Polytechnic Institute", Vol.4, (2006), pp.35-41.

      [8] V. Vanin, G. Virchenko, V. Vanin, â€Structural-parametric geometric modeling as a means of increasing the efficiency of group technologies in machine building†(in Ukrainian), Proceedings of the Tavria State Agrotechnological Academy, Vol.4, No.39, (2008), pp.9-21.

      [9] I. Taras, V. Virchenko, “Computer combinatorial-variation geometric modeling of engineering objectsâ€Â¸ Scientific Bulletin of the Politehnica University of Timisoara, Transactions on Hydrotechnics, Vol.58, No.72, (2013), pp.173-176.

      [10] V. Vanin, G. Virchenko, S. Virchenko, A. Nezenko, “Computer variant dynamic forming of technical objects on the example of the aircraft wingâ€, Eastern-European Journal of Enterprise Technologies, Vol.6, No.7, (2017), pp. 67-73, DOI: 10.15587/1729-4061.2017.117664

      [11] B. Palchevskyy, Research of technological systems (modeling, designing, optimization) (in Ukrainian), World, Lviv, (2011), 232 p.

      [12] A. Dalsky, A. Suslov, Yu. Nazarov, Mechanical engineering. Encyclopedia, Vol.III-3. The technology of manufacturing machine parts (in Russian), Mechanical Engineering, Moscow, (2010), 840 p.

      [13] B. Bazrov, Fundamentals of engineering technology (in Russian), Mechanical Engineering, Moscow, (2005), 736 p.

      [14] G. Virchenko, “Structural-parametric methods of approximation as a means of solving optimization problems†(in Ukrainian), Proceedings of the Tavria State Agrotechnological University, Vol.4, No.47, (2010), pp.61-66.

      [15] S. Virchenko, “Some aspects of computer dynamic geometric modeling of milling processes†(in Ukrainian), Modern modeling problems, Vol.10, (2017), pp.31-35.

      [16] Lyutenko, V., Orysenko, O., & Nadobko, V. (2018). Mathematical model for the manual vibration roller drive mechanism investigation. International Journal of Engineering and Technology(UAE), 7(3), 232-235. https://doi.org/10.14419/ijet.v7i3.2.14409

      [17] Nesterenko, M., Nesterenko, T., & Skliarenko, T. (2018). Theoretical studies of stresses in a layer of a light-concrete mixture, which is compacted on the shock-vibration machine. International Journal of Engineering and Technology(UAE), 7(3), 419-424. https://doi.org/10.14419/ijet.v7i3.2.14564

  • Downloads

  • How to Cite

    Virchenko, G., Martynov, V., Sergeychuk, O., & Usenko, V. (2018). Applying Using Structural-Parametric Geometric Models for Rational Design of Technological Processes in Mechanical Engineering. International Journal of Engineering & Technology, 7(4.8), 570-574. https://doi.org/10.14419/ijet.v7i4.8.27308

    Received date: 2019-02-11

    Accepted date: 2019-02-11

    Published date: 2018-10-13