Uniaxial Tensile Stress-Strain Response on the 3D Angle Interlock Woven Fabric Composite

  • Authors

    • F. M.Z. Nasrun
    • M. F. Yahya
    • M. R. Ahmad
    • S. A. Ghani
    2019-12-24
    https://doi.org/10.14419/ijet.v7i4.14.27711
  • Angle interlock woven fabric, woven fabric composite, stress-strain, weft density, draw-in plan

  • Abstract

    An experimental study have been performed to investigate the uniaxial tensile stress-strain response on the 3D angle interlock (3DAI) woven fabric composite. The tensile analysis were examined based on different woven fabric set-up parameter of draw-in plan ; pointed (DRW 1), broken (DRW 2), broken mirror (DRW 3), and straight (DRW 4). Meanwhile, the woven fabric composite were produced based on 22 and 25 pick.cm-1 of weft densities. The outcomes produced shown that woven composite sample with 25 pick.cm-1 on DRW 4 projected the highest stress response, 113 MPa. Extensive review indicated that DRW 1 and 4 gave better tensile stress-strain response than the other counterpart.

     

  • References

    1. [1] Ansar, M., W. Xinwei, and Z. Chouwei, Modeling strategies of 3D woven composites: A review. Composite Structures, 2011. 93(8): p. 1947-1963.

      [2] Mohamad Faizul Yahya, S.A.G.a.J.S., Effect of impactor shapes and yarn frictional effects on plain woven fabric puncture simulation. Textile Research Journal, 2014: p. 1-11.

      [3] Wang, C., Z. Lu, and L. Jin, A review on the mechanical performance and fatigue behavior of 3-D angle-interlock woven composites. The Journal of The Textile Institute, 2015: p. 1-9.

      [4] Mouritz, A.P., et al., Review of applications for advanced three-dimensional fibre textile composites. Composites: Part A, 1999. 30: p. 1445 - 1461.

      [5] M.F. Yahya, S.A. Ghani, and J. Salleh. Uniaxial Failure Resistance of Square-Isotropic 3D Woven Fabric Modelled with Finite Element Analysis. in 2011 IEEE International Symposium on Bussiness, Engineering and Industrial Applications (ISBEIA). 2011.

      [6] Unal, P.G., 3D Woven Fabrics, in Advances in Modern Woven Fabrics Technology. 2012. p. 91-120.

      [7] B.K Behera and B.P. Dash, An Experimental Investigation into the Mechanical Behaviour of 3D Woven Fabrics for Structural Composites. Fibers and Polymers 2014, 2013. 15(9): p. 1950 - 1955.

      [8] Dai, S., et al., Influence of fibre architecture on the tensile, compressive and flexural behaviour of 3D woven composites. Composites: Part A, 2015. 69: p. 195–207.

      [9] 9. A.R. Labanieh, et al., Evaluation Of The Elastic Behavior Of Multiaxis 3d-Woven Preforms By Numerical Approach. Journal of Composite Materials, 2014. 48(26).

      [10] J.S. Jones, et al., Comparative Study of 3-Dimensional Woven Joint Architectures for Composite Spacecraft Structures. 2011.

      [11] Chen, X., et al., Mouldability of Angle-Interlock Woven Fabrics for Technical Applications. Textile Research Journal, 2002. 72(3): p. 195-200.

      [12] J.S. Lim, et al., Effect of the Weaving Density of Aramid Fabrics on Their Resistance to Ballistic Impacts. Scientific Research Journal, 2012: p. 944 - 949.

      [13] F.O Aramide, I.O Oladele, & Folorunso, D. O. (2009). Evaluation of the Effect of Fiber Volume Fraction on the Mechanical Properties of a Polymer Matrix Composite. Leonardo Electronic Journal of Practices and Technologies(14), 134 - 141.

      [14] H. Gu, & Liyan, L. (2007). Research on tensile strength of linen/polypropylene composites with various fibre volume fractions. Materials & Design, 29(2008), 1485 - 1488. doi:10.1016/j.matdes.2007.07.004

      [15] M.P. Saiman, M.S. Wahab, & M.U. Wahit. (2014). The Effect of Fabric Weave on Tensile Strength of Woven Kenaf Reinforced Unsaturated Polyester Composite. International Colloquium on Textile Engineering, Fashion, Apparel & Design 2014.

      [16] ASTM D 5035 – 11(2015), in Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method). 2015, ASTM International.

  • Downloads

  • How to Cite

    M.Z. Nasrun, F., F. Yahya, M., R. Ahmad, M., & A. Ghani, S. (2019). Uniaxial Tensile Stress-Strain Response on the 3D Angle Interlock Woven Fabric Composite. International Journal of Engineering & Technology, 7(4.14), 430-433. https://doi.org/10.14419/ijet.v7i4.14.27711

    Received date: 2019-02-21

    Accepted date: 2019-02-21

    Published date: 2019-12-24