Analysis of power factor corrections for obtaining improved power factors of switching mode power supply

  • Authors

    • Dimov Stojce Ilcev Durban University of Technology (DUT)
    2020-09-30
    https://doi.org/10.14419/ijet.v9i3.31086
  • SMPS, PFC, PWM, MOSFET.

  • Abstract

    This article discusses such an important issue as the power factor of Switching Mode Power Supply (SMPS) and its improvement through Power Factor Correction (PFC). The power factor shows how effectively uses the consumption of electric energy by certain loads connected to the power distribution system with Alternative Current (AC), which is very critical for the electricity-producing industry. The number of power factors is a dimensionless value that can vary from -1 to 1. Thus, in an electric power system, a load with a low power factor draws more current than a load with a high power factor for the same amount of transferring useful power, which may cause overloading of the power grid and lead to over-expenditure of electricity. Otherwise, designing power factor correction (PFC) into modern switched-mode power supplies (SMPS) has evolved over the past few years due to the introduction of many new controller integrated circuits (IC). Today, it is possible to design a variety of PFC circuits with different modes of operation, each with its own set of challenges. As the number of choices has increased, so has the complexity of making the choice and then executing the new design. In this article, the design considerations and details of operation for the most popular approaches are provided.

     

     

  • References

    1. [1] Rossetto L., Spiazzi G. & Tenti P. (2000) "Control Techniques for Power Factor Correction Converters", University of Padova, Padova, Italy, 1-9.

      [2] SCI LLC (2007), "Power Factor Correction (PFC) Handbook, ON Semiconductor Headquarters", Denver, Colorado, US, 208.

      [3] Bistros F. A. & Santoso S. (2016) "Analysis of Power Factor Over Correction in a Distribution Feeder", University of Texas, Austin, US, 1-6.

      [4] Dranga O., Tse C.K, & Wong S.C. (2005) "Stability analysis of complete two-stage power factor correction power supplies", IEEE - European Conference on Circuit Theory and Design, Piscataway, NJ, US,1-4. https://doi.org/10.1109/ECCTD.2005.1522939.

      [5] Qiao C. & Smedley K. M. (2000) "A topology survey of single-stage power factor corrector with a boost type input-current-shaper", IEEE Applied Power Electronics Conf. (APEC2000), New Orleans, Louisiana, US, 460–467.

      [6] SCI LLC, (2019), "Overview of Power Factor Correction Approaches", Semiconductor Components Industries LLC, ON Semiconductor Headquarters, Phoenix, AZ, US, 1-8.

      [7] Hoseini M. S., Sadeghzadeh M. S. &, Berom A. J. (2015) "A new method for active power factor correction using a dual-purpose inverter in a flyback converter, Turkish Journal of Electrical Engineering & Computer Sciences, Istanbul, Turkey, 15.

      [8] Chandrakasan A. (1997), "Basics of Low Power Circuit and Logic Design", Massachusetts Institute of Technology, MA, US, 15.

      [9] Benini L., Micheli G.D. & Macii E., (2001) "Designing Low-Power Circuits", Universita di Bologna, Bolgnia, Italy, 23. https://doi.org/10.1109/7384.928306.

      [10] Grigore V. (2001) "Topological Issues in Single-Phase Power Factor Correction", Institute of Intelligent Power Electronics Publications Helsinki University of Technology, Helsinki, Finland, 114.

      [11] BEL Group, (2019) "Power Factor and Power Factor Correction", CUI INC, Tualatin, OR, US, 10.

  • Downloads

  • How to Cite

    Stojce Ilcev, D. (2020). Analysis of power factor corrections for obtaining improved power factors of switching mode power supply. International Journal of Engineering & Technology, 9(3), 826-829. https://doi.org/10.14419/ijet.v9i3.31086

    Received date: 2020-08-16

    Accepted date: 2020-08-29

    Published date: 2020-09-30