Development of reversed deep drawing without blank-holder for producing brass elliptical cup

  • Authors

    • Ali Hassan Institute of technology/Baghdad
    • Hani Aziz Tech. Eng.College/Baghdad
    • Ola Hussein Tech. Eng. College/Baghdad
    2018-04-17
    https://doi.org/10.14419/ijet.v7i2.8876
  • Reverse Deep Drawing, Elliptical Cup, Blank Holder, Clearance Ratio, ANSYS, Finite Element Method.

  • Abstract

    A new technique “Reverse Deep Drawing Process†without blank holder was adopted, for the single stage to produce an elliptical cup through an elliptical die. In this process an elliptical-cup is produced by pushing an elliptical blank using a hollow elliptical punch through an elliptical die in a single stroke. FEM via ANSYS is used to analyze this process. The clearance ratio was varied to study its effect on some parameters of this process like load, stress, strain, thickness distributions. A die with clearance =1mm and blank thickness=1mm gave the best drawability in this technique and no wrinkling observed on the product but it has minimum earring. Several attempted have been done to get the shape and dimensions of the blank, the major axis (a) =85mm & the minor axis (b) =65 mm was the better blank for this process to produce elliptical cup of major axis is twice minor axis. Good agreements are evident between the experimental and finite element results; the discrepancy is 4.0797% for load-extension and 0.852% for the wall thickness in minor axis and 1.145% in major axis.

  • References

    1. [1] W.K. Al-Samaraey."Studying the Effect of Die Geometry on Deep Drawing Operation Using Finite Element Method", (Ph,D)thesis , University of Technology , Department of Production Engineering and Metallurgy , (2003).

      [2] I.M. Hasab-Alla," A Finite Element Simulation and Experimental Verification of the Deep Drawing of Sheet Metals Without Blank-holder With Simultaneous Corrective Ironing", Ph.D thesis, Assiut university, Egypt,(1993).

      [3] I. M. Hassab-Allah, L. M. A. Hezam, and M. G. El-Sebaie,"A Novel Forming Technology For Drawing Square Cups" International Conference on Production Engineering &Design For Development, PEDD7, Cairo, February 7 – 9,(2006).

      [4] I. M. Hassab -Allah, "Finite Element Simulation of Square Cup Drawing Through a Conical Die " Fourth Assiut University Int. Conf. on Mech. Eng. Advanced Tech. For Indus. Prod., December 12-14 (2006).

      [5] Abdullah A. Dhaiban, M.-Emad S. Soliman, M.G. El-Sebaie," Finite Element Modeling and Experimental Results of Brass Elliptic Cups Using a New Deep Drawing Process Through Conical Dies" Journal of Materials Processing Technology; 214, 4; 828-838, (2014). https://doi.org/10.1016/j.jmatprotec.2013.11.025.

      [6] Mohsen Hassan, LabibHezam, Mohamed El-Sebaie, JudhaPurbolaksono,"Deep Drawing Characteristics of Square Cups Through Conical Dies", The International Conference on Technology of Plasticity, ICTP 2014, 19-24 October (2014).

      [7] Ravikant Patel, Manish Raj, AkshayKumar ," Finite Element Simulation for Determining the Optimum Blank Shape for Deep Drawing Process ", Int. Journal of Engineering Research and Applications , Vol. 4, Issue 11(Version - 5), pp.94-100, November (2014).

      [8] Ali Hassan Saleh ,Ammer Khalaf Ali, "Development Technique for Deep Drawing Without Blank Holder to Produce Circular Cup of Brass Alloy", International Journal of Engineering & Technology, 4 (1) 187-195,(2015) https://doi.org/10.14419/ijet.v4i1.3516.

      [9] M.A. Hassan, I. M. Hassab-Allah, L. M. A. Hezam, N. A. Mardi, M. Hamdi ,"Deep Drawing of Asymmetric Cups Through Conical Die without Blank Holder ",Proceedings of the World Congress on Engineering ,Vol II ,WCE, July 1 - 3,( 2015).

      [10] Ammer Khalaf Ali, "Effect of Some Geometrical and Operational Parameters of Reversed Drawing Process, Without Blank Holder, on the Stress Distribution ", M.Sc. thesis, Engineering Technical College-Baghdad, (2014).

  • Downloads

  • How to Cite

    Hassan, A., Aziz, H., & Hussein, O. (2018). Development of reversed deep drawing without blank-holder for producing brass elliptical cup. International Journal of Engineering & Technology, 7(2), 578-583. https://doi.org/10.14419/ijet.v7i2.8876

    Received date: 2017-12-18

    Accepted date: 2018-03-07

    Published date: 2018-04-17