Basic design of a cooling system for nylon 6, 6 process

  • Authors

    • Karthik Silaipillayarputhur Ph. D King Faisal University http://orcid.org/0000-0003-2290-6615
    • Nasser Al Mulhim King Faisal University
    • Abdullah Al Mulhim King Faisal University
    • Mohammed Arfaj King Faisal University
    • Ahmed Al Naim King Faisal University
    2018-06-14
    https://doi.org/10.14419/ijet.v7i3.9421
  • Cooling System Design, Preliminary Heat Exchanger Design, Performance Charts.

  • Abstract

    The project concentrates on the basic design of a cooling system for rapidly cooling nylon 6, 6 polymer fibers using cold air. The ambient air after pre-treatment in the air-washer is available at 72°F all year round. Based on the company’s throughput, it is required to supply (quench) air at 58°F. Nylon 6, 6 polymer after thorough polymerization is distributed through 16 quench cabinets and each quench cabinet requires approximately 530 ft3/min (cubic feet per minute, CFM) of air. The project concentrates on the basic design of a cooling system wherein air at the required mass flow rate is supplied at 58°F for the quenching process. A basic design of the refrigeration cycle and heat exchangers were considered in this work. In the development of the basic design for heat exchanger, performance charts were developed. Performance charts describe the performance of the heat exchanger in terms of fundamental dimensionless parameters. Using performance charts it was clearly seen that increasing the number of transfer units (NTU) doesn’t necessarily increase the rate of heat transfer. Increasing the NTU beyond an optimum value is pointless and increases the capital cost of the heat exchanger. The preliminary design involves selection of appropriate NTU and capacity rate ratio for the heat exchanger. From the capacity rate ratio and NTU, it is fairly straight forward to extrapolate the detailed design for the heat exchanger. A cooling system model was developed for the design process and for the simulation of the cooling system.

     

     

  • References

    1. [1] Kays, W. M., and London A. L., Compact Heat Exchangers, 3rd Ed., McGraw-Hill, New York, 1984.

      [2] Rohsenow, W. M., Heat Exchangers – Basic Methods, in Heat Exchangers Thermal-Hydraulic Fundamentals and Design, Hemisphere Publishing Corporation, Washington D.C., 1982.

      [3] Domingos, J. D., Analysis of Complex Assemblies of Heat Exchangers, Int. J. Heat Mass Transfer, Vol. 12, pp. 537-548, 1969. https://doi.org/10.1016/0017-9310(69)90037-4.

      [4] Pignotti, A. and Shah, R. K., Effectiveness-number of transfer units relationships for heat exchanger complex flow arrangements, Int. J. Heat Mass Transfer, Vol. 35, No. 5, pp. 1275-1291, 1992. https://doi.org/10.1016/0017-9310(92)90184-T.

      [5] Shah, R. K. and Pignotti, A., Thermal Analysis of Complex Crossflow Exchangers in Terms of Standard Configurations, J. Heat Transfer, Vol. 115, pp. 353-359, 1993. https://doi.org/10.1115/1.2910686.

      [6] Mott, J. E. and Mills, R. R., Computerized Design of a Minimum Cost Heat Exchanger, ASME Paper 72-HT-26, 1972.

      [7] Genic, S. B., Jacimovic, B. M., and Genic, V. B., Economic optimization of pipe diameter for complete turbulence, Energy and Buildings, Vol. 45, pp. 335-338, 2012. https://doi.org/10.1016/j.enbuild.2011.10.054.

      [8] Kovaric, M., Optimal Heat Exchangers, J. Heat Transfer, Vol. 111, pp. 287-293, 1989. https://doi.org/10.1115/1.3250676.

      [9] Ramananda Rao, K., Shrinivasa, U., and Srinivasan, J., Synthesis of Cost-Optimal Shell-and Tube Heat Exchangers, Heat Transfer Engineering, Vol. 12, No. 3, pp. 47-55, 1991. https://doi.org/10.1080/01457639108939756.

      [10] Caputo, A. C., Pelagagge, M. P., and Salini, P., Heat Exchanger Design Based on Economic Optimization, Paper CIT06-0387, ENCIT 2006 -ABCM, Curitiba, Brazil, 2006.

      [11] Silaipillayarputhur, K., Al-Muhaysh, K., and Al Yahya, O., 2016, “Design of a Dowtherm A Pumping Systemâ€, International Journal of Applied Engineering Research, ISSN: 0973-4562, Volume 11, Issue 1, page 265-272, Research India Publications, India.

      [12] Bergman, T. L., Lavine, A. S., Incropera, F. P., and DeWitt, D. P., Fundamentals of Heat and Mass Transfer, 7th Ed., John Wiley, Hoboken, NJ, 2011.

      [13] Campbell, J.M., Gas Conditioning and Processing, Volume 2: The Equipment Modules, 9th Edition, 2nd Printing, Editors Hubbard, R. and Snow–McGregor, K., Campbell Petroleum Series, Norman, Oklahoma, 2014.

  • Downloads

  • How to Cite

    Silaipillayarputhur Ph. D, K., Al Mulhim, N., Al Mulhim, A., Arfaj, M., & Al Naim, A. (2018). Basic design of a cooling system for nylon 6, 6 process. International Journal of Engineering & Technology, 7(3), 977-990. https://doi.org/10.14419/ijet.v7i3.9421

    Received date: 2018-02-07

    Accepted date: 2018-05-29

    Published date: 2018-06-14