The effects of particle size distribution and sintering conditions on bending strength of sintered Ni-30%Fe alloys

  • Authors

    • Mxolisi B. Shongwe Thswane University of Technology, Pretoria
    • Olawale O. Ajibola University of Johannesburg
    • Munyadziwa M. Ramakokovhu Thswane University of Technology, Pretoria
    • Peter A. Olubambi University of Johannesburg
    2018-07-23
    https://doi.org/10.14419/ijet.v7i3.9618
  • Sintering, Grains, Bending Strength, Particle Size.

  • Abstract

    This work reports effect of the powder grain size distributions on the bending strength sintered Ni-30%Fe alloys obtained from mixed coarse-fine micron size metal powders. Two dissimilar particle sizes of Ni and Fe metal powders were mixed by subjecting them to translational and rotational agitations using the T2F Turbula Shaker Mixer. The mixed powders were moulded using graphite dies and sintered in vacuum and at constant pressure using Spark Plasma Sintering furnace (HHPD-25). The ratios of the two metals were varied as well as the sintering temperature and time. The morphology and microstructures of both powders and sinters were studied using field emission scanning electron microscopy (JSM-7600F) equipped with energy dispersive X-ray spectrometer (EDS) facilities. The phases in the sintered specimens were characterized by X-ray diffraction (XRD). The densities of the samples were determined, The Vickers microhardness at room temperature and bending strength of the sintered alloy specimens were measured. Comparatively, low heating rate (50 oC/min) produced enhanced microstructures hence higher bonding, bending strength and densification than samples at high heating rate (150 oC/min).

     

     

  • References

    1. [1] H. Czichos, D. Klaffke, E. Santner and M. Woydt. “Advances in tribology: the materials point of viewâ€, Wear, Vol. 190, No 2. (1995), pp 155-161. doi.org/10.1016/0043-1648 (96)80014-7.

      [2] ASM Specialty Handbook: Nickel, Cobalt, and their Alloys (#06178G), ASM International, 2000.

      [3] J.C. Hey, and A.P. Jardine, “Shape memory TiNi synthesis from elemental powders†Material Science and Engineering A., Vol. 188, No 1-2, (1994), pp291-300. https://doi.org/10.1016/0921-5093(94)90384-0.

      [4] B.Y. Li, L.J. Rong, & Y.Y. Li, “Porous NiTi alloy prepared from elemental powder sinteringâ€, Journal Materials Research. Vol. 13, No 10, (1998), pp2847-2851.

      https://doi.org/10.1557/JMR.1998.0389.

      [5] A. Bansiddhi and D.C. Dunand, “Shape-memory NiTi–Nb foamsâ€, Journal Materials Research. Vol. 24, No 6, (2009), pp 2107-2117. https://doi.org/10.1557/jmr.2009.0256.

      [6] T. Majewski, "Investigations of Production Processes of W-Re-Ni and W-Re-Ni-Fe Heavy Metals", Solid State Phenomena, Vol. 165, (2010), pp. 124-129.

      https://doi.org/10.4028/www.scientific.net/SSP.165.124.

      [7] M.L. Marucci, G. Fillari, P. King, and K. S. Narasimhan, “A review of current. sinter-hardening technology†PM 2004 World Congress, Vienna, Austria.

      [8] J. Räthel, M. Herrmann and W. Beckert. "Temperature distribution for electrically conductive and non-conductive materials during Field Assisted Sintering (FAST)". Journal European Ceramic Society. Vol 29, No 8, (2009), pp 1419–1425. https://doi.org/10.1016/j.jeurceramsoc.2008.09.015.

      [9] A. Zavaliangos, J. Zhang, M. Krammer, and JR. Groza. “Temperature evolution during field activated sintering “Material Science Engineering A, Vol. 379, No 1-2, (2004), pp.218–228. https://doi.org/10.1016/j.msea.2004.01.052.

      [10] M.B.Shongwe, M.M.Ramakokovhu, S.Diouf, M.O.Durowoju, B.A. Obadele, R. Sule, M. L. Lethabane, P. A. Olubambi, "Effect of starting powder particle size and heating rate on spark plasma sintering of FeNi alloys", Journal of Alloys and Compounds, Vol. 678, (2016), pp 241-248.

      https://doi.org/10.1016/j.jallcom.2016.03.270.

      [11] M.B. Shongwe, I. M. Makena, M.M. Ramakokovhu, T. Langa, P.A. Olubambi. "Sintering behavior and effect of ternary additions on the microstructure and mechanical properties of Ni–Fe-based alloy". Particulate Science and Technology. Vol 35, April 2017. https://doi.org/10.1080/02726351.2017.1298686.

      [12]M.B. Shongwe, I. M. Makena, O.O. Ajibola, P.A. Olubambi, F.V. Adams. "Investigation of ternary additions on corrosion resistance of spark plasma sintered 50Ni40Fe alloys in H2SO4 and NaCl". Bulletin of the Chemical Society of Ethiopia. Vol. 32, No. 2, pp 337-349.

      [4] B.Y. Li, L.J. Rong, & Y.Y. Li, “Porous NiTi alloy prepared from elemental powder sinteringâ€, Journal Materials Research. Vol. 13, No 10, (1998), pp2847-2851

      [5] A. Bansiddhi and D.C. Dunand, “Shape-memory NiTi–Nb foamsâ€, Journal Materials Research. Vol. 24, No 6, (2009), pp 2107-2117. doi.org/10.1557/jmr.2009.0256

      [6] T. Majewski, "Investigations of Production Processes of W-Re-Ni and W-Re-Ni-Fe Heavy Metals", Solid State Phenomena, Vol. 165, (2010), pp. 124-129. doi.org/10.4028/www.scientific.net/SSP.165.124

      [7] M.L. Marucci, G. Fillari, P. King, and K. S. Narasimhan, “A review of current. sinter-hardening technology†PM 2004 World Congress, Vienna, Austria

      [8] J. Räthel, M. Herrmann and W. Beckert. "Temperature distribution for electrically conductive and non-conductive materials during Field Assisted Sintering (FAST)". Journal European Ceramic Society. Vol 29, No 8, (2009), pp 1419–1425

      [9] A. Zavaliangos, J. Zhang, M. Krammer, and JR. Groza. “Temperature evolution during field activated sintering “Material Science Engineering A, Vol. 379, No 1-2, (2004), pp.218–228,

  • Downloads

  • How to Cite

    B. Shongwe, M., O. Ajibola, O., M. Ramakokovhu, M., & A. Olubambi, P. (2018). The effects of particle size distribution and sintering conditions on bending strength of sintered Ni-30%Fe alloys. International Journal of Engineering & Technology, 7(3), 1581-1584. https://doi.org/10.14419/ijet.v7i3.9618

    Received date: 2018-02-19

    Accepted date: 2018-05-04

    Published date: 2018-07-23